Full List

Search

Recent Vulnerabilities

• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43227 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: clocksource/drivers/sh_tmu: Always leave device running after probe The TMU device can be used as both a clocksource and a clockevent provider. The driver tries to be smart and power itself on and off, as well as enabling and disabling its clock when it's not in operation. This behavior is slightly altered if the TMU is used as an early platform device in which case the device is left powered on after probe, but the clock is still enabled and disabled at runtime. This has worked for a long time, but recent improvements in PREEMPT_RT and PROVE_LOCKING have highlighted an issue. As the TMU registers itself as a clockevent provider, clockevents_register_device(), it needs to use raw spinlocks internally as this is the context of which the clockevent framework interacts with the TMU driver. However in the context of holding a raw spinlock the TMU driver can't really manage its power state or clock with calls to pm_runtime_*() and clk_*() as these calls end up in other platform drivers using regular spinlocks to control power and clocks. This mix of spinlock contexts trips a lockdep warning. ============================= [ BUG: Invalid wait context ] 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 Not tainted ----------------------------- swapper/0/0 is trying to lock: ffff000008c9e180 (&dev-power.lock){-...}-{3:3}, at: __pm_runtime_resume+0x38/0x88 other info that might help us debug this: context-{5:5} 1 lock held by swapper/0/0: ccree e6601000.crypto: ARM CryptoCell 630P Driver: HW version 0xAF400001/0xDCC63000, Driver version 5.0 #0: ffff8000817ec298 ccree e6601000.crypto: ARM ccree device initialized (tick_broadcast_lock){-...}-{2:2}, at: __tick_broadcast_oneshot_control+0xa4/0x3a8 stack backtrace: CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.18.0-arm64-renesas-09926-gee959e7c5e34 #1 PREEMPT Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) Call trace: show_stack+0x14/0x1c (C) dump_stack_lvl+0x6c/0x90 dump_stack+0x14/0x1c __lock_acquire+0x904/0x1584 lock_acquire+0x220/0x34c _raw_spin_lock_irqsave+0x58/0x80 __pm_runtime_resume+0x38/0x88 sh_tmu_clock_event_set_oneshot+0x84/0xd4 clockevents_switch_state+0xfc/0x13c tick_broadcast_set_event+0x30/0xa4 __tick_broadcast_oneshot_control+0x1e0/0x3a8 tick_broadcast_oneshot_control+0x30/0x40 cpuidle_enter_state+0x40c/0x680 cpuidle_enter+0x30/0x40 do_idle+0x1f4/0x280 cpu_startup_entry+0x34/0x40 kernel_init+0x0/0x130 do_one_initcall+0x0/0x230 __primary_switched+0x88/0x90 For non-PREEMPT_RT builds this is not really an issue, but for PREEMPT_RT builds where normal spinlocks can sleep this might be an issue. Be cautious and always leave the power and clock running after probe.
• CVE-2026-43226 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: net/rds: No shortcut out of RDS_CONN_ERROR RDS connections carry a state "rds_conn_path::cp_state" and transitions from one state to another and are conditional upon an expected state: "rds_conn_path_transition." There is one exception to this conditionality, which is "RDS_CONN_ERROR" that can be enforced by "rds_conn_path_drop" regardless of what state the condition is currently in. But as soon as a connection enters state "RDS_CONN_ERROR", the connection handling code expects it to go through the shutdown-path. The RDS/TCP multipath changes added a shortcut out of "RDS_CONN_ERROR" straight back to "RDS_CONN_CONNECTING" via "rds_tcp_accept_one_path" (e.g. after "rds_tcp_state_change"). A subsequent "rds_tcp_reset_callbacks" can then transition the state to "RDS_CONN_RESETTING" with a shutdown-worker queued. That'll trip up "rds_conn_init_shutdown", which was never adjusted to handle "RDS_CONN_RESETTING" and subsequently drops the connection with the dreaded "DR_INV_CONN_STATE", which leaves "RDS_SHUTDOWN_WORK_QUEUED" on forever. So we do two things here: a) Don't shortcut "RDS_CONN_ERROR", but take the longer path through the shutdown code. b) Add "RDS_CONN_RESETTING" to the expected states in "rds_conn_init_shutdown" so that we won't error out and get stuck, if we ever hit weird state transitions like this again."
• CVE-2026-43226 • published on May 6, 2026 In the Linux kernel, the following vulnerability has been resolved: net/rds: No shortcut out of RDS_CONN_ERROR RDS connections carry a state "rds_conn_path::cp_state" and transitions from one state to another and are conditional upon an expected state: "rds_conn_path_transition." There is one exception to this conditionality, which is "RDS_CONN_ERROR" that can be enforced by "rds_conn_path_drop" regardless of what state the condition is currently in. But as soon as a connection enters state "RDS_CONN_ERROR", the connection handling code expects it to go through the shutdown-path. The RDS/TCP multipath changes added a shortcut out of "RDS_CONN_ERROR" straight back to "RDS_CONN_CONNECTING" via "rds_tcp_accept_one_path" (e.g. after "rds_tcp_state_change"). A subsequent "rds_tcp_reset_callbacks" can then transition the state to "RDS_CONN_RESETTING" with a shutdown-worker queued. That'll trip up "rds_conn_init_shutdown", which was never adjusted to handle "RDS_CONN_RESETTING" and subsequently drops the connection with the dreaded "DR_INV_CONN_STATE", which leaves "RDS_SHUTDOWN_WORK_QUEUED" on forever. So we do two things here: a) Don't shortcut "RDS_CONN_ERROR", but take the longer path through the shutdown code. b) Add "RDS_CONN_RESETTING" to the expected states in "rds_conn_init_shutdown" so that we won't error out and get stuck, if we ever hit weird state transitions like this again."