-
CVE-2026-98752
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
tty: port: fix tty_port_tty_vhangup() race
Drivers rely on tty_port_tty_vhangup() to synchronously hang up their
ports before tearing down resources as part of deregistration (e.g. on
physical disconnect).
If tty_port_tty_vhangup() races with another hangup it may however
return before the port has been shut down. This is in turn can lead to
use-after-free and NULL-pointer dereferences in racing ioctls (including
a synchronous hangup) and in processing of racing asynchronous hangups
(carrier loss).
Add the missing serialisation to tty_port_tty_vhangup() and
tty_port_hangup() so that the former does not return until the port has
been shut down also when there is a racing hangup.
Note that serial core does not use tty_port_hangup(), but it already
holds the port mutex when clearing port-tty and shutting down the port
in uart_hangup().
-
CVE-2026-98740
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
EDAC/altera: Drop __init from ECC setup paths for re-probe safety
Sashiko reports:
"Does suppressing sysfs unbinding fully prevent the execution of freed __init
memory? If altr_sysmgr_regmap_lookup_by_phandle() returns -EPROBE_DEFER, the
probe is deferred until after __init memory is freed."
The a10 EDAC .setup callbacks (sdmmc, ethernet, nand, dma, usb, qspi) and
their helpers (altr_init_a10_ecc_device_type, altr_init_a10_ecc_block) were
marked __init. These run from the probe path, which may execute after init
memory is freed -- e.g. a probe deferred via -EPROBE_DEFER that only succeeds
once a late/module dependency appears, or a manual unbind/rebind. Calling
__init code then dereferences freed memory. Remove __init so these functions
remain valid at runtime.
-
CVE-2026-98738
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Serialize SMP remote OOB data access
build_pairing_cmd() looks up remote OOB data and copies its contents
without holding hdev-lock, which serializes the list's writers. After
SMP finds an entry, a concurrent management Remove Remote OOB Data
command can unlink and free it before SMP reads its present flag or
copies its random and confirmation values. Removal can also invalidate
an entry while the lookup is still traversing the list.
KASAN reported:
BUG: KASAN: slab-use-after-free in build_pairing_cmd+0x948/0x9b0
Call Trace:
build_pairing_cmd+0x948/0x9b0
smp_recv_cb+0x459f/0x8110
l2cap_recv_frame+0xf14/0x9190
l2cap_recv_acldata+0xa64/0xd40
hci_rx_work+0x4ca/0x730
Allocated by task 87:
hci_add_remote_oob_data+0x11d/0x530
add_remote_oob_data+0x282/0x400
hci_sock_sendmsg+0x1033/0x1ea0
Freed by task 93:
hci_remote_oob_data_clear+0x108/0x1c0
remove_remote_oob_data+0x198/0x220
hci_sock_sendmsg+0x1033/0x1ea0
Taking hdev->lock in build_pairing_cmd() would recurse for callers that
already hold it and invert the device-to-L2CAP lock order on the receive
path. Add a per-device remote_oob_lock instead, held across the SMP
lookup and copies and by the add, remove and clear helpers. Cover
initialization and in-place updates as well, so SMP cannot read partially
initialized or updated OOB values. Release the mutex on allocation
failure, preserving the existing error return.
The new critical sections acquire no device, connection or channel locks.
Writers retain their existing hdev->lock protection, which continues to
serialize the other readers without changing their locking or behavior.
-
CVE-2026-98735
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize ACL scheduling with channel deletion
hci_chan_sent() selects a channel under RCU but drops the read lock before
accessing chan-conn and returning the channel. The ACL and LE schedulers
then use its packet queue and update its transmit counters without any
protection against channel deletion.
After TX selects a channel and releases RCU, a disconnect command timeout
on the separate request workqueue can run hci_conn_failed() and
l2cap_conn_del(). hci_chan_del() can then unlink the channel, complete
synchronize_rcu(), purge its queue and free it before TX resumes. This
causes use-after-free both in hci_chan_sent() and in its callers.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_chan_sent+0x892/0x9b0
Workqueue: hci0 hci_tx_work
Call Trace:
hci_chan_sent+0x892/0x9b0
hci_tx_work+0x5e6/0xb70
Allocated by task 91:
hci_chan_create+0xe3/0x350
l2cap_conn_add.part.0+0x12/0xa30
l2cap_chan_connect+0x110d/0x1b60
l2cap_sock_connect+0x310/0x530
Freed by task 99:
hci_chan_del+0x11f/0x170
l2cap_conn_del+0x4f1/0x800
l2cap_connect_cfm+0x88c/0xd30
hci_conn_failed+0x150/0x250
hci_abort_conn_sync+0x3e3/0x800
hci_cmd_sync_run+0x7e/0xc0
hci_abort_conn+0x105/0x1f0
disconnect_sync+0x157/0x290
hci_cmd_sync_work+0x13c/0x290
Hold the existing device mutex across channel selection and transmission
in both schedulers to serialize them with channel teardown. Keep timeout
handling outside the critical sections because hci_link_tx_to() acquires
the same mutex. This also permits the transmit path to sleep, unlike
extending the RCU read-side critical section across packet submission.
-
CVE-2026-98732
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: fix buffer over-read in btintel_hw_error()
The "Exception info %s" print uses skb-data + 1, but the 12-byte
payload is not guaranteed to be NUL-terminated and can be read past
its end.
Bound the print with "%.*s" and skb->len - 1.
-
CVE-2026-98719
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Nullify "have run CPUs" mask pointer when freeing it
Nullify have_run_cpus when freeing the mask, particularly in the error path
of __sev_guest_init(), so that KVM doesn't have to subtly use sev-active
to track whether or not the mask has been freed. As pointed out by Sashiko,
blindly freeing the mask in sev_vm_destroy() results in a double-free if
the mask is freed if __sev_guest_init() fails.
Throw the logic in a helper as nullifying the pointer is frustratingly
difficult and weird due to have_run_cpus being a single-entry array when
CPUMASK_OFFSTACK=n. Deliberately don't use CPUMASK_VAR_NULL, as it's not
directly assignable when the cpumask is on-stack, e.g. requires using a
local variable and a memcpy(), which is beyond ridiculous. Furthermore,
while clearing the on-stack bitmask is an unnecessary and arguably unwanted
side effect, KVM absolutely relies on '0' being the "null" value given that
the struct is zero-allocated.
Opportunistically add an alloc() helper to pair with free(); there are just
enough call sites to make doing so worthwhile.
-
CVE-2026-98717
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Bail from shadow walks if the root is invalid or a dummy
When walking shadow page tables, immediately terminate the walk if the root
is a "dummy" root, i.e. a root whose top-level page table is backed by the
zero page, but otherwise doesn't exist. If memslot creation races with a
stage-2 page fault (EPT violation or #NPF) from L2, then if the stars align,
KVM will attempt to walk shadow page tables using the zero page and hit a
NULL pointer deref.
BUG: kernel NULL pointer dereference, address: 0000000000000021
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP
CPU: 30 UID: 1000 PID: 941 Comm: qemu Not tainted 7.2.0-rc2-1b731e5ded48-next-vm #1741 PREEMPTLAZY
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:__kvm_mmu_invalidate_addr+0xea/0x210 [kvm]
Call Trace:
TASK
kvm_mmu_invalidate_addr+0x92/0xe0 [kvm]
__kvm_inject_emulated_page_fault+0x67/0x80 [kvm]
ept_page_fault+0x160/0x850 [kvm]
kvm_mmu_do_page_fault+0x102/0x1f0 [kvm]
kvm_mmu_page_fault+0x8e/0x6b0 [kvm]
vmx_handle_exit+0x163/0x640 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x960/0x2120 [kvm]
kvm_vcpu_ioctl+0x2c7/0x970 [kvm]
__x64_sys_ioctl+0x90/0xd0
do_syscall_64+0x67/0x5f0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f606d0b53bb
Opportunistically harden the shadow walks against fully invalid roots, but
WARN, as all callers are expected/required to pre-check for a valid root.
Don't WARN in the dummy root case as the whole point of using a dummy root
is to provide a root that's valid enough to enter the guest, i.e. it should
Just Work for all flows except those that *need* to know about dummy roots.
Alternatively, KVM could allocate a dedicated page and associated shadow
page structure for the dummy root, which is very tempting as it such an
approach should be more resilient against unexpected behavior. But that
would be a much larger and thus riskier change than simply terminating
walks of dummy roots.
-
CVE-2026-98708
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: keep paired old chanctx alive
An in-place replacement keeps reciprocal replace_ctx pointers between
the old WILL_BE_REPLACED chanctx and the new REPLACES_OTHER chanctx.
However, the early free paths only consider assigned and reserved link
users when deciding whether to free the old chanctx.
That lets the old chanctx be freed too early while the replacement
partner still points back to it, either when the last assigned link is
released or when that link successfully reassigns to another existing
context. Later unreserve and switch-finalization paths can then follow a
stale replace_ctx pointer.
Keep a paired old chanctx alive until the replacement pair has been torn
down. Apply the same check to both __ieee80211_link_release_channel()
and ieee80211_link_use_reserved_reassign(). If the replacement is later
abandoned, ieee80211_link_unreserve_chanctx() already tears down the
pairing before freeing the old chanctx once no users remain.
-
CVE-2026-98703
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: minstrel_ht: validate fixed rate index
The fixed_rate_idx debugfs file is a plain u32 attribute, so any value
can be written to it. minstrel_ht_update_stats() then copies the value
into mi-max_tp_rate[] and mi->max_prob_rate, and
minstrel_ht_set_rate() uses MI_RATE_GROUP()/MI_RATE_IDX() to index
minstrel_mcs_groups[] (42 entries) and mi->groups[].rates[] (10 entries)
with it.
Writing e.g. 65535 selects group 4095 and rate index 15, far outside
both arrays. The out-of-bounds entries are dereferenced and updated as
struct minstrel_rate_stats (retry counts, etc.), so the invalid index
corrupts adjacent kernel memory. With CONFIG_UBSAN_BOUNDS the access is
reported as an array-index-out-of-bounds in minstrel_ht_set_rate().
Only a valid group/rate pair, or U32_MAX to disable fixed rate
processing, can be used safely, so reject any other value when the
debugfs file is written.
The file is only reachable through a root-only debugfs mount, so this is
not a privilege boundary. The out-of-bounds access is still a bug that
must not be reachable through a writable debugfs attribute.
-
CVE-2026-98702
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: reject invalid 320 MHz CSA bandwidth
The HT/VHT channel definition validator can receive a 320 MHz
bandwidth indication from a received CSA frame on a non-6 GHz link.
It warns for this unsupported width but continues with an uninitialized
vht_operation.chan_width, which is then read by
ieee80211_chandef_vht_oper(). With panic_on_warn enabled, this lets a
received frame panic the kernel.
Reject the channel definition before entering the VHT operation
conversion. This preserves the existing CSA fallback while avoiding
both the warning and the uninitialized read.
-
CVE-2026-98701
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: release mesh path quota on failed additions
Repeated failed or duplicate mesh path additions can exhaust
MESH_MAX_MPATHS while the path table holds fewer paths, which stops new
paths to reachable destinations from being created.
mesh_path_add() reserves a slot before allocating and inserting a path.
If allocation fails, the function returns without releasing the slot. If
the rhashtable insertion reports an error or an existing destination, the
function discards its candidate but retains the reservation. No new path
is installed in any of these cases.
Release the reservation whenever the candidate is not installed.
-
CVE-2026-98700
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: set info-band for 802.3 encap offload frames
Unlike the 802.11 TX paths, ieee80211_8023_xmit() does not set
info->band from the channel context on non-MLD interfaces. It stays at
0, so ieee80211_get_tx_rates() uses the wrong band for these frames.
Set it the same way as ieee80211_build_hdr(): drop the frame if there is
no channel context, and leave the band at 0 on MLD interfaces.
-
CVE-2026-98697
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix dynamic id driver deregistration race
Only free the dynamic ids after having deregistered the driver and
removed the "new_id" attribute to avoid leaking any id added by a racing
write to the attribute.
-
CVE-2026-98695
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix ioctl hangup race
The tty ioctls can race with hangup and end up calling into a tty driver
for a device that is already gone or powered down.
Serialise the callbacks using the tty port mutex and add the missing
checks to make sure the port has not been hung up before accessing port
driver data or hardware.
This specifically avoids dereferencing a NULL-pointer if a device is
disconnected during lengthy break signalling.
Note that TIOCGICOUNT and TIOCMIWAIT do not access port driver data or
hardware and are therefore not affected by the race.
-
CVE-2026-98693
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Hold a router reference for each allocated HopID
tb_stop() drops the reference to all DP tunnels but does not deactivate
them, thus nothing cancels a dprx_work still in flight (which holds its
own tunnel reference) and the tunnel can outlive tb_switch_remove(). The
HopID releases in tb_path_free() then operate on freed IDAs and trigger
warnings like
ida_free called for id=8 which is not allocated.
This can be triggered by unbinding the driver while a DP tunnel is still
waiting for the DPRX capabilities read to finish. On the Apple NHI
unplugging the cable runs into just that reliably because the read can
never finish right now and because the unplug powers down the entire
USB4 complex and removes the NHI device.
Take a router reference whenever an input or output HopID is allocated
and drop it again after the HopID is released. This keeps the ports and
their HopID IDAs alive for as long as they are used.
The KUnit tests allocate routers without ever registering their devices
so initialize the embedded struct device there as well and drop its
initial reference when the test is finished.
-
CVE-2026-98689
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Don't access a DP tunnel after its DPRX read was canceled
tb_dp_dprx_work() checks -dprx_canceled before it takes tb->lock so it
misses a tb_dp_dprx_stop() that could not cancel the already running
work. It then polls the DPRX capabilities and runs the callback for a
tunnel that has already been torn down while the domain is suspending or
going away.
This can be hit by cancelling the DPRX read from outside the ordered
tb->wq: During suspend tb_disconnect_and_release_dp() does just this and
with a later patch tb_stop() will do it as well. The latter in combination
with the Apple NHI where the DPRX read never completed is how I hit
this.
Check the flag with tb->lock held instead and check it again in
tb_dp_tunnel_active() because the callback runs after the lock has been
dropped again.
Also clear the flag in tb_dp_dprx_start() so that it only ever describes
the work that is currently in flight.
-
CVE-2026-98687
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Reject oversized XDomain properties responses
tb_xdp_properties_request() allocates room for 45 data dwords in its
252-byte response buffer. The XDomain length field is six bits wide,
however, and a malicious peer can set it to 63. After the fixed response
fields are subtracted, the driver treats this as 48 data dwords.
Commit 322e93448d90 ("thunderbolt: Clamp XDomain response data copy to
allocation size") only bounds the copy against data_len. If data_len is
at least 48, memcpy() reads 192 bytes from the 180-byte res-data array,
causing a 12-byte heap out-of-bounds read. Commit 4db2bd2ed478
("thunderbolt: Limit XDomain response copy to actual frame size") limits
the earlier copy but does not constrain this header-derived length.
Reject response data lengths that exceed the allocated source buffer
before copying them into the assembled property block.
-
CVE-2026-98683
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
smb: client: flush dirty data before zeroing a range
smb3_zero_range() emulates FALLOC_FL_ZERO_RANGE by invalidating the
page cache over the target range with truncate_pagecache_range() and
then issuing FSCTL_SET_ZERO_DATA to the server.
Dirty data was only flushed conditionally, when the range reached or
extended EOF. For a purely interior zero range that does not reach
EOF, no flush happened, so a dirty folio overlapping the range could
be written back to the server after the FSCTL and refill the range
that was just zeroed with stale data.
Fix this by unconditionally flushing and waiting for dirty data in the
range before invalidating the page cache and issuing
FSCTL_SET_ZERO_DATA, exactly as was done for smb3_punch_hole() in
commit d7d2adcd022b ("smb/client: flush dirty data before punching a
hole"); the two paths are structurally identical here.
This is observed as generic/363 randomly reading stale data where a
zeroed range is expected against Windows Server.
-
CVE-2026-98682
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
smb: client: drain and invalidate before server-side copy/clone
cifs_file_copychunk_range() and the clone (FICLONE) path of
cifs_remap_file_range() do not serialise the destination page cache
against the server-side copy the way the other server-side range
operations (smb3_zero_range(), smb3_punch_hole(), smb3_collapse_range()
and smb3_insert_range()) do.
cifs_file_copychunk_range() invalidates the destination range with
filemap_invalidate_inode(), which takes and drops the mapping's
invalidate_lock internally, so the lock is no longer held when the
copychunk ioctl is issued. It also never drains in-flight netfs I/O on
the target. The clone path never takes the invalidate_lock at all (only
i_rwsem), uses a bare truncate_inode_pages_range() and likewise does not
drain outstanding I/O.
As a result an asynchronous destination writeback can complete after the
server-side copy/clone has run and reinstate stale data over the region
just written by the server, corrupting the file. This is the same class
of corruption as commit d7d2adcd022b ("smb/client: flush dirty data
before punching a hole") and has been seen randomly in generic/363
against Windows Server.
Fix both paths to follow the established ordering: hold the target
mapping's invalidate_lock across the flush and invalidation of the
destination and the server ioctl, and call netfs_wait_for_outstanding_io()
on the target to drain in-flight writes before the ioctl is issued. Only
the target inode's invalidate_lock is required, as the source is merely
flushed and not invalidated; i_rwsem (already held via
lock_two_nondirectories()) is acquired before the invalidate_lock,
matching the VFS lock ordering. Since filemap_invalidate_inode() takes
that same lock internally, replace it with its own unmap/flush/invalidate
steps instead of calling it, and return early on a zero-length copy to
avoid a range underflow.
-
CVE-2026-98680
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kionix-kx022a: Prevent memory leak and fix state
The driver allocates memory for samples at buffer enable path. If regmap
operation fails in the kx022a_fifo_enable() at the buffer enable path, the
allocated memory is never freed. Furthermore, the state information and
previous hardware configuration(s) aren't undone, potentially leaving
WMI interrupts and buffers enabled, or driver state flags wrong.
Free the memory and revert the hardware configuration and state flags on
error path.