-
CVE-2026-97495
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Check bounds on allocate_doorbell
allocated_doorbell has an option to set the doorbell id
to a specific value (used by CRIU). This value was not
bounds checked.
Check to confirm it's less than KFD_MAX_NUM_OF_QUEUES_PER_PROCESS.
-
CVE-2026-97494
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: validate and share PSP fw_pri_buf copies via psp_copy_fw
Change psp_copy_fw from void to int: return -ENODEV when drm_dev_enter
fails, and -EINVAL when the image size is zero or larger than the
1 MiB PSP private buffer.
Replace open-coded memset/memcpy into fw_pri_buf with psp_copy_fw.
-
CVE-2026-97488
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
qnx4: handle set_blocksize failures
qnx4 uses buffer_heads, which don't handle block size PAGE_SIZE well.
Without this, mounting will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call.
-
CVE-2026-97485
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
omfs: handle set_blocksize failures
omfs uses buffer_heads, which don't handle block size PAGE_SIZE well.
Without this, mounting we will hit the
BUG_ON(offset >= folio_size(folio));
in folio_set_bh on the first __bread_gfp call.
-
CVE-2026-97481
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
serial: 8250: fix possible ISR soft lockup
There are rare cases in which the host gets stuck in the ISR because it
is flooded with messages during the startup phase.
The reason for the soft lockup in the ISR is the missing FIFO error IRQ
(FIFOE) handling. Not handling it and reporting IRQ_HANDLED triggers
the IRQ immediately again.
Fix this by adding a check for the FIFOE status and clearing the FIFO
if no data is ready (DR).
This behavior was observed on an AM62L device which uses the OMAP 8250
driver. Fix it for all 8250 drivers, since the OMAP driver's special
IRQ setup handling may trigger this behavior more frequently, but it
is not ensured that other 8250 drivers aren't affected.
-
CVE-2026-97479
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
driver core: Avoid warning when removing a device while its supplier is unbinding
During driver removal, the following warning can appear:
WARNING: CPU: 1 PID: 139 at drivers/base/core.c:1497 __device_links_no_driver+0xcc/0xfc
...
Call trace:
__device_links_no_driver+0xcc/0xfc (P)
device_links_driver_cleanup+0xa8/0xf0
device_release_driver_internal+0x208/0x23c
device_links_unbind_consumers+0xe0/0x108
device_release_driver_internal+0xec/0x23c
device_links_unbind_consumers+0xe0/0x108
device_release_driver_internal+0xec/0x23c
device_links_unbind_consumers+0xe0/0x108
device_release_driver_internal+0xec/0x23c
driver_detach+0xa0/0x12c
bus_remove_driver+0x6c/0xbc
driver_unregister+0x30/0x60
pci_unregister_driver+0x20/0x9c
lan966x_pci_driver_exit+0x18/0xa90 [lan966x_pci]
This warning is triggered when a consumer is removed because the links
status of its supplier is not DL_DEV_DRIVER_BOUND and the link flag
DL_FLAG_SYNC_STATE_ONLY is not set.
The topology in terms of consumers/suppliers used was the following
(consumer --- supplier):
i2c -----------> OIC ----> PCI device
| ^
| |
+---> pinctrl ---+
When the PCI device is removed, the OIC (interrupt controller) has to be
removed. In order to remove the OIC, pinctrl and i2c need to be removed
and to remove pinctrl, i2c need to be removed. The removal order is:
1) i2c
2) pinctrl
3) OIC
4) PCI device
In details, the removal sequence is the following (with 0000:01:00.0 the
PCI device):
driver_detach: call device_release_driver_internal(0000:01:00.0)...
device_links_busy(0000:01:00.0):
links->status = DL_DEV_UNBINDING
device_links_unbind_consumers(0000:01:00.0):
0000:01:00.0--oic link->status = DL_STATE_SUPPLIER_UNBIND
call device_release_driver_internal(oic)...
device_links_busy(oic):
links->status = DL_DEV_UNBINDING
device_links_unbind_consumers(oic):
oic--pinctrl link->status = DL_STATE_SUPPLIER_UNBIND
call device_release_driver_internal(pinctrl)...
device_links_busy(pinctrl):
links->status = DL_DEV_UNBINDING
device_links_unbind_consumers(pinctrl):
pinctrl--i2c link->status = DL_STATE_SUPPLIER_UNBIND
call device_release_driver_internal(i2c)...
device_links_busy(i2c): links->status = DL_DEV_UNBINDING
__device_links_no_driver(i2c)...
pinctrl--i2c link->status is DL_STATE_SUPPLIER_UNBIND
oic--i2c link->status is DL_STATE_ACTIVE
oic--i2c link->supplier->links.status is DL_DEV_UNBINDING
The warning is triggered by the i2c removal because the OIC (supplier)
links status is not DL_DEV_DRIVER_BOUND. Its links status is indeed set
to DL_DEV_UNBINDING.
It is perfectly legit to have the links status set to DL_DEV_UNBINDING
in that case. Indeed we had started to unbind the OIC which triggered
the consumer unbinding and didn't finish yet when the i2c is unbound.
Avoid the warning when the supplier links status is set to
DL_DEV_UNBINDING and thus support this removal sequence without any
warnings.
-
CVE-2026-97477
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
RDMA/counter: Fix num_counters leak on bind_qp failure in alloc_and_bind()
When __rdma_counter_bind_qp() fails in alloc_and_bind(), the error path
jumps to err_mode which frees the counter without decrementing
port_counter-num_counters. The only place that decrements is
rdma_counter_free(), which is unreachable since the counter was never
successfully bound.
This leak accumulates across repeated failures, permanently preventing
the port from switching to AUTO mode (-EBUSY in __counter_set_mode())
and blocking the MANUAL→NONE auto-revert in rdma_counter_free(). When
the mode was NONE before the call, the MANUAL mode set by
__counter_set_mode() also leaks since the revert logic is never
reached.
Add an err_bind label between the num_counters increment and the
existing err_mode label. It decrements num_counters and mirrors the
MANUAL→NONE revert from rdma_counter_free(), ensuring the port state
is fully restored on bind failure.
-
CVE-2026-97476
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
rds: filter RDS_INFO_* getsockopt by caller's netns
The RDS_INFO_* family of getsockopt(2) options reads several
file-scope global lists that are not per-netns:
rds_sock_info / rds6_sock_info,
rds_sock_inc_info / rds6_sock_inc_info - rds_sock_list
rds_tcp_tc_info / rds6_tcp_tc_info -> rds_tcp_tc_list
rds_conn_info / rds6_conn_info,
rds_conn_message_info_cmn (for the *_SEND_MESSAGES and
*_RETRANS_MESSAGES variants),
rds_for_each_conn_info (for RDS_INFO_IB_CONNECTIONS)
-> rds_conn_hash[]
The handlers do not filter by the caller's network namespace.
rds_info_getsockopt() has no netns or capable() check, and
rds_create() has no capable() check, so AF_RDS is reachable from
an unprivileged user namespace. As a result, an unprivileged
caller in a fresh user_ns plus netns can read the bound address
and sock inode of every RDS socket on the host, the peer address
of incoming messages on every RDS socket on the host, the peer
address and TCP sequence numbers of every rds-tcp connection on
the host, and the peer address and RDS sequence numbers of every
RDS connection on the host.
The rds-tcp transport is reachable from a non-initial netns (see
rds_set_transport()), so a one-shot init_net gate at
rds_info_getsockopt() would deny legitimate per-netns visibility
to rds-tcp callers. Instead, filter at each handler by comparing
the netns of the caller's socket to the netns of the list entry,
or to rds_conn_net(conn) for connection paths. Only copy entries
whose netns matches the caller. Counters (RDS_INFO_COUNTERS) are
aggregate statistics and remain global.
Reproducer (KASAN VM, rds and rds_tcp loaded): an AF_RDS socket
binds 127.0.0.1:4242 in init_net as root. A child process enters
a fresh user_ns plus netns and opens AF_RDS there, then calls
getsockopt(SOL_RDS, RDS_INFO_SOCKETS). Before this change, the
child sees the init_net socket. After this change, the child
sees zero entries.
Drop the rds_sock_count, rds_tcp_tc_count, and rds6_tcp_tc_count
globals. v2 used them for the size precheck and lens->nr; v3
replaced the precheck with a per-ns count from a first pass over
the list, so the globals have no remaining readers. The matching
increments and decrements in rds_create()/rds_destroy_sock() and
rds_tcp_set_callbacks()/rds_tcp_restore_callbacks() go away with
them. Reported by the kernel test robot under clang W=1.
-
CVE-2026-97475
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
thermal/drivers/tegra/soctherma: Switch to devm cooling device registration
Use devm_thermal_of_cooling_device_register() to simplify resource
management and avoid manual cleanup in error paths.
As a side effect this change has the benefit of solving an existing
issue. Before, the function tegra_soctherm_remove() only called
debugfs_remove_recursive() and never called thermal_cooling_device_unregister()
for any of the cooling devices registered here.
After the driver removal, the thermal framework's cdev list would
still hold references to thermal_cooling_device objects whose devdata
pointer (ts) pointed to memory already freed by the platform device's
devm cleanup.
With this change, the cooling device is unregistered when the driver
is removed, thus fixing the issue above.
-
CVE-2026-97469
•
published on September 25, 2026
PostgreSQL Anonymizer contains a vulnerability that allows unprivileged masked users to repeatedly call the anon.hash() function and collects (seed, hash_output) pairs to perform an offline brute-force attack and deduce the salt. A masked role can run a RESTRICTED function when the call is placed inside the sub-select. The problem is resolved in PostgreSQL Anonymizer 3.2.3 and later versions
-
CVE-2026-97453
•
published on September 24, 2026
In the Linux kernel, the following vulnerability has been resolved:
ACPICA: validate byte_count in acpi_ps_get_next_package_length()
Validate package length reading in acpi_ps_get_next_package_length().
-
CVE-2026-97620
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Flush LSC untyped L1 dataport cache after rcs/ccs batches
emit_render_cache_flush() sets PIPE_CONTROL0_HDC_PIPELINE_FLUSH to
flush the L2/HDC data cache before fence signalling, but it never
requests a flush of the LSC untyped L1 data cache via the 'Untyped
Data-Port Cache Flush Enable' bit in PIPE_CONTROL DWord0[11].
Per the Bspec, in 3D pipeline mode HDC Pipeline Flush is documented to
also flush/invalidate the untyped L1 cache, but only depending on how
HDC_CHICKEN0[13:11] is programmed. Starting with MTL, this coupling
between HDC Pipeline Flush and the untyped L1 cache flush no longer
holds in practice, regardless of how HDC_CHICKEN0 is programmed, so
relying on it is not safe on newer platforms such as BMG. Mesa's Vulkan
driver (anv) has been assuming the kernel flushes both caches between
submissions, and hit user-visible corruption in apps such as Llama.cpp
because of this gap; it now works around it by flushing both caches
again from userspace at the end of every command buffer.
Correctness between submissions on the same queue is userspace's
responsibility and belongs in Mesa, not the kernel. However, for
security we must ensure stale data can't leak through the untyped L1
dataport cache once memory is reclaimed or evicted, which requires the
KMD to flush it before releasing memory for reuse.
Prior to MTL, HDC_CHICKEN0 could be programmed (as already done for
DG2 via Wa_22010960976/Wa_14013347512) to reliably keep HDC Pipeline
Flush coupled to the untyped L1 cache flush, so those platforms are
unaffected. Mesa's own anv driver found that on MTL the HW
disconnected the two independently of how HDC_CHICKEN0 is programmed,
and could not bring the old behavior back even by writing the register
by hand; see Mesa commit 7c2ff46a4fc3 ("anv: don't prevent L1 untyped
cache flush in 3D mode"). The kernel can't reliably request the flush
from the CS on MTL either, so restrict the new PIPE_CONTROL bit to
GRAPHICS_VERx100 = 2000 (Xe2 and later), where it can be relied on.
Explicitly set PIPE_CONTROL0_UNTYPED_DATAPORT_CACHE_FLUSH together
with PIPE_CONTROL0_HDC_PIPELINE_FLUSH in emit_render_cache_flush() on
Xe2 and later, so the L1 data cache is known clean before memory is
released for reuse, without depending on undocumented
platform-specific HDC_CHICKEN0 behavior.
Bspec: 56551
(cherry picked from commit 434514b6fe731e873808297c268fc52cdf4a1ce6)
-
CVE-2026-97616
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: release all action references on NEWACTION failure
When a batched RTM_NEWACTION request replaces an existing action,
tcf_idr_check_alloc() takes a temporary reference on it. If a later
action fails to initialize, tcf_action_destroy() uses strict release
semantics to clean up the actions initialized so far. For an action
bound to a filter, the strict check returns -EPERM without dropping
the temporary reference.
This error also makes tcf_action_destroy() return before releasing
subsequent entries. Any new action initialized between the bound
action and the failing entry is leaked together with its reserved
IDR slot, preventing reuse of its index.
Use tcf_idr_release() to drop each reference held by the batch without
rejecting bound actions. This allows cleanup to continue through all
initialized entries and preserves the module reference release when
an action is destroyed. Explicit action deletion and flushing retain
their separate bind-count checks.
-
CVE-2026-97613
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: mana: Reserve extra CQ slot for the fence completion CQE
The RX completion queue is sized to hold exactly one CQE per posted RX WQE.
MANA_FENCE_RQ makes hardware post an additional CQE_RX_OBJECT_FENCE after
the packet CQEs. The current sizing reserves no extra slot for it and in
rare cases, CQ has no guaranteed slot for the fence CQE when it is full of
packet CQEs. This can lead to dropping the fence completion while the
driver waits holding RTNL lock throughout the timeout duration.
Reserve one extra CQE slot for CQE_RX_OBJECT_FENCE. mana_gd_alloc_memory()
requires queue_size to be a power-of-two and at least MANA_PAGE_SIZE;
the reservation pushes cq_size past a power-of-two, so round up the CQ size
in mana_create_rxq().
-
CVE-2026-97610
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix uninitialized return value in netfs_unbuffered_write()
If preparation of the first subrequest fails,
netfs_unbuffered_write() exits its loop before ret is initialized. The
empty-iterator check can do the same.
For synchronous writes, netfs_unbuffered_write_iter_locked() may then
return an unrelated error instead of wreq-error. This is reachable
through CIFS if cifs_prepare_write() fails to reopen the file or obtain
credits.
Initialize ret to 0 so the caller returns wreq->error if no data was
written, or the number of bytes already written otherwise.
Found with Clang's -Wconditional-uninitialized.
-
CVE-2026-97607
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
vdpa: ifcvf: Put device on unsupported feature error
Route unsupported provisioned features through the common error path after
vdpa_alloc_device() so the allocated device and adapter pointer are
released consistently.
-
CVE-2026-97600
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
ieee802154: cc2520: fix FIFOP work use-after-free
The FIFOP interrupt handler queues cc2520_fifop_irqwork. On removal,
cc2520_remove() only flushes the work. The devm-managed FIFOP IRQ
remains active until after -remove() returns and can queue the work
again after that flush, allowing it to run after the private data is
released.
Disable the work with disable_work_sync() instead of flushing it, so
the handler can no longer queue it once removal begins. Destroy the
buffer mutex last, since the worker and the stop callback invoked
through ieee802154_unregister_hw() both take it.
Found by an in-house static analysis tool.
-
CVE-2026-97594
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
landlock: Fix use-after-free of the source's parent directory
current_check_refer_path() reads old_dentry-d_parent without holding a
reference nor a lock on it, and then dereferences it in
collect_domain_accesses() and in the audit record.
A reference on a child does not pin its parent: __d_move() reassigns
dentry->d_parent and drops the reference the child held on its former
parent. hook_path_rename() is not affected because the rename path
calls lock_rename() before the hook, so the source cannot be reparented
under it. hook_path_link() has no such protection: filename_linkat()
holds a reference on the source dentry but neither locks nor references
its parent, so a concurrent rename(2) can reparent the source while
security_path_link() runs, and the former parent can then be removed and
freed while the hook walks it.
A process can trigger this after entering a Landlock domain that handles
at least one filesystem access right. The process can then race a
linkat(2) loop against rename(2) and rmdir(2):
BUG: KASAN: slab-use-after-free in collect_domain_accesses+0x278/0x290
Read of size 4 at addr ffff888160bd53f4 by task llrepro2/549
collect_domain_accesses+0x278/0x290
current_check_refer_path+0x952/0x1120
security_path_link+0x1be/0x320
filename_linkat+0x342/0x6d0
__x64_sys_linkat+0xfa/0x150
Freed by task 562:
kmem_cache_free+0x139/0x4c0
i_callback+0x4b/0x80
rcu_core+0x7dc/0x10a0
Take a reference on the dentry selected as the source parent, using
dget() for the common-mount-root case and dget_parent() otherwise.
Release it after the hierarchy walk and synchronous audit logging.
[mic: Clarify the caller, reachability, and reference handling]
-
CVE-2026-97589
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
s390/crypto: Fix wrong return code to engine in asynch callbacks
When crypto_finalize_hash_request() or
crypto_finalize_skcipher_request() explicitly completes a request, the
do_one_request callback must return 0 to indicate successful
handling. Returning a negative error code causes the crypto engine to
assume the driver failed to take ownership and triggers a second
completion via crypto_request_complete(), resulting in a double
completion. This pattern occurs in paes_s390.c 4 times and once in
phmac_s390.c.
Fixed in phmac_do_one_request() and all four paes do_one_request
callbacks (ecb, cbc, ctr, xts) by returning 0 after explicit
finalization instead of propagating the error code.
-
CVE-2026-97586
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
afs: Fix missing kunmap in afs_dir_search_bucket()
Fix afs_dir_search_bucket() to kunmap the block it's using in the "bad:"
path.