-
CVE-2026-99188
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: dwmac1000: clear the RGMII status interrupt
Since commit 2e2c878a3141 ("net: stmmac: remove SGMII/RGMII/SMII
interrupt handling") nothing on the RGMII path reads GMAC_RGSMIIIS, so
RGSMIIIS stays pending behind GMAC_INT_MASK from the first link change
on. stmmac_resume() resets the MAC in stmmac_hw_setup(); the reset sets
GMAC_INT_MASK to 0 until dwmac1000_core_init() writes the mask again,
and the pending status storms the line:
dwmac_dma_interrupt: unexpected status 04000000
A register dump at the first message on ODROID-HC4 showed it:
core int_status 00000001 int_mask 00000000 pmt 00000000 rgsmiiis 0000000d
When the resume thread runs on the CPU that takes the MAC interrupt,
the storm starves it: a soft lockup, then a watchdog reset or a hang.
Read GMAC_RGSMIIIS in dwmac1000_irq_status() when the status is not
masked, as the driver did before 2e2c878a3141; the read clears it.
Wake-on-LAN resume from s2idle with the resume thread and the MAC
interrupt on one CPU: Helios64 (dwmac-rk), 7.3-rc6, soft-locked in 3 of
3 resumes without a fix and in 0 of 10 with this patch; it ran with an
out-of-tree dwmac-rk change that keeps the GMAC powered across suspend.
ODROID-HC4 (dwmac-meson8b): 0 of 10 with this patch, 2 of 2 without a
fix on a 7.3-rc5 build. irq_rgmii_n went up by one per resume.
-
CVE-2026-99181
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
autofs: ignore notification errors from a replaced pipe
autofs_notify_daemon() takes a reference to the current notification
pipe under wq_mutex, then drops the mutex before writing the request. The
write can block while the daemon enters catatonic mode and installs a
replacement pipe.
If the old pipe's reader is then closed, the delayed write returns -EPIPE
and the generic error path enters catatonic mode again. That transition
acts on the current superblock state, closes the replacement pipe, and
releases the new daemon generation's wait queues.
Only enter catatonic mode when the pipe which failed is still the current
pipe. Factor the already-locked transition so the identity check and state
change are atomic with respect to another replacement.
This was reproduced on v7.3-rc5-337-gff47652a4b66c in a local QEMU guest.
An unprivileged UID 65534 lookup filled the old packet pipe before a
normal CATATONIC/SETPIPEFD restart. On the unmodified kernel, the new pipe
received HUP and both a pending victim lookup and a later lookup failed
with ENOENT in two out of two fresh-mount runs.
With this change, the new pipe remained active, received an intact
304-byte request, and both victim lookups completed in two out of two
runs. Normal lookup and restart-without-a-blocked-writer controls passed.
No KASAN, oops, refcount, or lock diagnostic was observed. A source
reproducer and complete local logs are available privately on request.
The demonstrated impact is limited to denial of a shared autofs service
during a legitimate daemon restart. No memory corruption, information leak,
privilege escalation, or code execution primitive was observed.
-
CVE-2026-99179
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
watch_queue: Fix note pool publication race in watch_queue_set_size()
There is a race between watch_queue_set_size() and post_one_notification().
watch_queue_set_size() publishes wqueue-notes, notes_bitmap, nr_pages and
nr_notes with plain stores, and post_one_notification() reads them with
plain loads under a different lock, so nothing orders the four stores
against the poster's loads: depending on the build, notes can be stored
last (gcc 14 on x86-64 does this). Since keyctl_watch_key() lets a watch
attach to a queue before it is sized, post_one_notification() can already
be running on another CPU at that moment: it reads nr_notes > 0, passes
its bounds check, and then reads notes while it is still NULL,
dereferencing notes[0].
An unprivileged user triggers this reliably by watching one of its own
keys through a notification pipe and racing ioctl(IOC_WATCH_QUEUE_SET_SIZE)
on that pipe against keyctl(KEYCTL_SETPERM) on the key from another CPU,
triggering:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:post_one_notification.isra.0+0xa2/0x1e0
Call Trace:
__post_watch_notification+0x148/0x180
keyctl_setperm_key+0x119/0x130
do_syscall_64+0x108/0x4c0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Kernel panic - not syncing: Fatal exception in interrupt
Fix this by publishing nr_notes last with smp_store_release(), and by
reading it once with smp_load_acquire() in post_one_notification() before
the bitmap and the page array are touched. A poster that observes a
non-zero nr_notes then also observes the pool behind it; one that observes
zero drops the notification as before.
-
CVE-2026-99176
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
KVM: nVMX: Reset MMU back to the root MMU if loading L2 state fails for !VM-Entry
Reset the vCPU's MMU pointer back to the root MMU if loading L2 state fails
in the "not from VM-Entry" case, i.e. when emulating RSM or handling
KVM_SET_NESTED_STATE. Failure to unwind the MMU pointer results in KVM
trying to run L1 with a nested MMU, and is especially problematic if the
vCPU manages to free its nested state before the VM crashes. Constructing
the root for a nested EPT MMU goes through vmcs12, which is dynamically
allocated/freed when nVMX is enabled/disabled. And so if the nested state
is freed with the MMU still pointing at the nested MMU, KVM will hit a NULL
pointer deref when attempting to get L1=L2 EPTP.
BUG: kernel NULL pointer dereference, address: 0000000000000078
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 114a2d067 P4D 111743067 PUD 11141f067 PMD 0
Oops: Oops: 0000 [#1] SMP
CPU: 20 UID: 1000 PID: 1272 Comm: nested_tdp_faul Not tainted 7.3.0-rc4-8c89f11d1a99b-sink-vm #1914 PREEMPTLAZY
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:nested_ept_get_eptp+0xb/0x10 [kvm_intel]
Call Trace:
TASK>
kvm_mmu_load+0xcd/0x870 [kvm]
kvm_arch_vcpu_ioctl_run+0x18f5/0x1f80 [kvm]
kvm_vcpu_ioctl+0x2c7/0x970 [kvm]
__x64_sys_ioctl+0x90/0xd0
do_syscall_64+0x9c/0x4d0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x47491b
Modules linked in: kvm_intel kvm irqbypass
CR2: 0000000000000078
---[ end trace 0000000000000000 ]---
RIP: 0010:nested_ept_get_eptp+0xb/0x10 [kvm_intel]
[sean: write changelog]
-
CVE-2026-99173
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
eventfs: Free the eventfs_inode after an rcu grace period too
tracefs_d_revalidate() reads -is_freed of the eventfs_inode that
dentry->d_fsdata points to, and ->d_revalidate() is called in rcu
pathwalk mode with nothing but rcu_read_lock() held. The dentry itself
stays around for such a walker, but tracefs_d_release() drops its
reference to the eventfs_inode when the dentry is killed, and
release_ei() then frees it after a grace period of eventfs_srcu. An
SRCU grace period doesn't wait for rcu_read_lock() sections, so the
walker can read an eventfs_inode that is already gone.
With a pathwalk held up in tracefs_d_revalidate() while the dentry goes
away:
BUG: KASAN: slab-use-after-free in tracefs_d_revalidate+0x76/0x90
Read of size 1 at addr ff1100010152d8d0 by task walker/97
Call Trace:
TASK>
tracefs_d_revalidate+0x76/0x90
lookup_fast+0x320/0x640
path_lookupat+0x160/0xb00
filename_lookup+0x1f1/0x5b0
vfs_statx+0xd7/0x3b0
vfs_fstatat+0x4d/0x90
__do_sys_newfstatat+0xa0/0x100
do_syscall_64+0x10e/0x5e0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
__kmalloc_cache_noprof+0x249/0x560
eventfs_create_dir+0x7a/0x590
event_create_dir+0x2fb/0xcf0
trace_add_event_call+0xbf/0x150
[...]
Freed by task 11:
kfree+0x1db/0x5b0
srcu_invoke_callbacks+0x3a3/0x620
process_one_work+0x937/0x1810
worker_thread+0x4f1/0xd60
Before commit 8e556432477e ("eventfs: Use SRCU for freeing
eventfs_inodes") release_ei() used call_rcu(), which covered the walker,
while eventfs_iterate() needs the SRCU grace period. Wait for both and
chain call_rcu() from the SRCU callback.
-
CVE-2026-99171
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
ntfs3: free the sbi after a grace period
If the "nocase" mount option ntfs3 uses custom hash and dentry compare
functions. Both access ntfs3 superblock private information in rcu
pathwalk. ntfs_put_super() and ntfs3_kill_sb() drop the info without any
rcu delay. A lookup that's still inside the filesystem when the last
reference to the mount is dropped causes a UAF. With a pathwalk held up
in ntfs_d_hash() while the last reference to the mount goes away:
BUG: KASAN: slab-use-after-free in ntfs_nls_to_utf16+0x752/0x940
Read of size 8 at addr ff1100010453c850 by task walker/99
Call Trace:
TASK
ntfs_nls_to_utf16+0x752/0x940
ntfs_d_hash+0x22b/0x500
link_path_walk+0x11ad/0x1d30
path_lookupat+0x63/0xb00
filename_lookup+0x1f1/0x5b0
vfs_statx+0xd7/0x3b0
[...]
Allocated by task 95:
__kmalloc_cache_noprof+0x249/0x560
ntfs_init_fs_context+0x2db/0x5a0
alloc_fs_context+0x52e/0xc70
[...]
Freed by task 98:
kfree+0x1db/0x5b0
deactivate_locked_super+0x9c/0xf0
cleanup_mnt+0x9f/0x130
task_work_run+0x131/0x250
The bug is currently masked by the grace period in namespace_unlock()
for umount(2). Keep the necessary information until the filesystem
private info is freed and free it with an rcu delay.
ntfs3_free_sbi() now runs from an rcu callback and drops the upcase
table via ntfs_put_shared(). So switch s_shared_lock over to
spin_lock_bh(). Otherwise the callback can deadlock against a task
holding the lock on the same cpu.
-
CVE-2026-99170
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
namespace: a mount that copy_tree() leaves out can't take over a lock
Since commit c62a4766937e ("move_mount: transfer MNT_LOCKED") a mount
can be moved beneath a locked mount. The lock moves from the old cover
to the new mount which takes over the job of hiding what's under it and
the old cover can be unmounted. That works as long as the new mount
stays. But the caller picks the new mount and copy_tree() leaves a
mount of a mount namespace file out of every copy made without
CL_COPY_MNT_NS_FILE, together with everything mounted on it, and never
looks at MNT_LOCKED. unshare(CLONE_NEWNS) and mount propagation make
such copies.
So a task that is root in its own user namespace gets rid of a locked
cover on a file without a race and without touching the filesystem
below it. It makes a child with a mount namespace of its own, binds the
child's /proc/pid/ns/mnt beneath the cover with MOVE_MOUNT_BENEATH,
which hands the lock to that bind, and calls unshare(CLONE_NEWNS). The
new mount namespace has nothing on the file. That's the usual way to
mask a single file, a bind of /dev/null or of an empty file. With a
bind of an ordinary file the file stays covered.
copy_tree() already refuses to leave out a locked unbindable mount with
-EPERM since commit df7342b24018 ("mount: Don't allow copying
MNT_UNBINDABLE|MNT_LOCKED mounts"). Do the same for a locked mount of a
mount namespace file. That also covers a tree copied with
CL_COPY_MNT_NS_FILE and attached into a mount namespace of another user
namespace where lock_mnt_tree() locks it. Note that unshare(CLONE_NEWNS)
and clone(CLONE_NEWNS) fail with EPERM from such a mount namespace from
then on. The mount can't be left out and it can't be unmounted.
And refuse to move a mount of a mount namespace file beneath a locked
mount in the first place. Otherwise the task ends up with a mount it
can't unmount and an unshare() that fails for good.
Chris also found a second mount that goes away by itself, a clone of an
automounted mount that shrink_submounts() took along with its parent.
Commit f78ddcc87224 ("namespace: never expire a locked mount") took
care of that one.
Chris's reproducer is appended. Mode nsfile reads SECRET after the
unshare() on 7.3-rc7, with this patch the move_mount() fails with
EINVAL and the file stays covered. nsfile-control uses an ordinary file
and reads MASK both ways.
// SPDX-License-Identifier: GPL-2.0
/*
* Get rid of a locked cover with MOVE_MOUNT_BENEATH.
*
* The "admin" (root) makes a tmpfs W:
* W/D file, holds SECRET, covered by a bind of a file with MASK
* W/Dd/inner file, holds SECRET, Dd is covered by a bind of a directory
* whose "inner" holds MASK
* W/own directory of uid 1000 with the file "mine" and the
* directory "minedir", whose "inner" holds MINE
* W/dbg debugfs, mode 755. dbg/tracing is an automount point
* The "attacker" is uid 1000. It enters a new user namespace with a new mount
* namespace, so W and both covers are locked there.
*
* usage: prog MODE
* plain put a bind of own/mine beneath the cover of D, unmount the cover
* nsfile put a bind of the mount namespace file of a child beneath the
* cover of D, then unshare(CLONE_NEWNS)
* nsfile-control the same with a bind of own/mine
* shrink put a bind of the automounted tracefs beneath the cover of Dd,
* unmount the cover, put a tmpfs beneath W, call umount(W), which fails
* shrink-control the same with a bind of own/minedir
* The environment variable AUTOMOUNT_DIR names another automount point for "shrink".
*/
#define _GNU_SOURCE
#include
#include
#include
#include
#include
#include
#include
#include
#include
---truncated---
-
CVE-2026-99167
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
net/sched: fix use-after-free in __tcf_action_put()
__tcf_action_put() decrements the reference count before decrementing the
binding count. Another thread can free the action between these operations,
causing the binding-count update to access freed memory. KASAN reports it
as:
BUG: KASAN: slab-use-after-free in __tcf_action_put+0x327/0x340
Write of size 4 at addr ff11000000d46420 by task tc-put-pause/64
Hold the action IDR mutex across both counter updates and IDR removal,
keeping cleanup outside the lock.
-
CVE-2026-99165
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
sctp: revalidate output stream after association connect wait
When message interleaving is enabled, the first send waits for association
establishment before building its data chunks. The wait drops the socket
lock, and handshake processing can reduce the output stream count to the
peer-advertised inbound stream count. sctp_stream_init() then frees the
extension of every removed stream.
The sender resumes with the stream that it checked before the wait. If the
peer removed that stream, sctp_outq_tail() later dereferences its NULL
extension. Fatal-oops policies then panic the host.
KASAN: null-ptr-deref in range [0x38-0x3f]
RIP: sctp_outq_tail+0x49e/0xaa0
Call Trace:
sctp_primitive_SEND
sctp_sendmsg_to_asoc
sctp_sendmsg
A range check alone is insufficient. Stream reconfiguration can grow the
output count again while the lock is released without recreating extensions
freed by the earlier shrink. The stream can then be in range while its
extension remains NULL. The send-buffer wait has the same issue.
Factor the range and extension checks into a helper and repeat both after
each send-path wait that drops the socket lock. Once the lock is
reacquired, the validation remains stable through data creation and
queueing.
If validation fails after the connect wait, the auto-created association is
already established. Return ESRCH so the existing caller path keeps it
under state-machine ownership instead of freeing it directly, which would
leave protocol, counter and socket state inconsistent.
-
CVE-2026-99157
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
scsi: bsg: Pass reply_len to bsg_setup_queue() to fit UFS ARPMB replies
bsg-lib allocates a 96-byte (SCSI_SENSE_BUFFERSIZE) reply buffer per
job, but struct ufs_rpmb_reply is 104 bytes: a 40-byte struct
ufs_bsg_reply followed by a 64-byte EHS. When an Advanced RPMB command
returns an EHS, ufshcd_advanced_rpmb_req_handler() copies it right after
the 40-byte header and writes 8 bytes past the end of the buffer.
Let each BSG transport pass its reply buffer size to bsg_setup_queue()
and have ufs_bsg request sizeof(struct ufs_rpmb_reply), so the full
reply reaches user space. Other transports keep SCSI_SENSE_BUFFERSIZE.
-
CVE-2026-99152
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi: Validate the task named by a management response
__iscsi_complete_pdu() fetches the task for five response types from one
place and checks only that the index resolved:
case ISCSI_OP_LOGOUT_RSP:
case ISCSI_OP_LOGIN_RSP:
case ISCSI_OP_TEXT_RSP:
case ISCSI_OP_SCSI_TMFUNC_RSP:
case ISCSI_OP_NOOP_IN:
task = iscsi_itt_to_task(conn, hdr-itt);
if (!task)
return ISCSI_ERR_BAD_ITT;
iscsi_itt_to_task() bounds the index against cmds_max and looks at
nothing else, so a target can name any slot in the pool, including one
that has never been used. task->conn is then NULL, and both
iscsi_nop_out_rsp() and iscsi_complete_task() dereference it. One
unsolicited NOP-In is enough; a Text Response carrying the same ITT
crashes in iscsi_complete_task() instead.
Require the task to be in flight and not a SCSI command, the way
iscsi_itt_to_ctask() does for the command opcodes.
[ 6.298634] Oops: general protection fault, probably for non-canonical address 0xdffffc000000000c: 0000 [#1] SMP KASAN NOPTI
[ 6.298642] KASAN: null-ptr-deref in range [0x0000000000000060-0x0000000000000067]
[ 6.298652] CPU: 1 UID: 0 PID: 111 Comm: iscsistart Not tainted 7.2.0-rc5-ISCSI1-gf5098b6bae76 #1 PREEMPT(lazy)
[ 6.298654] Hardware name: QEMU Ubuntu 24.04 PC v2 (i440FX + PIIX, arch_caps fix, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
[ 6.298656] RIP: 0010:iscsi_nop_out_rsp.constprop.0+0x46/0x160
[ 6.298691] Code: c1 ea 03 48 83 ec 08 80 3c 02 00 0f 85 f5 00 00 00 48 b8 00 00 00 00 00 fc ff df 48 8b 6b 58 48 8d 7d 60 48 89 fa 48 c1 ea 03 80> 3c 02 00 0f 85 c0 00 00 00 48 8b 45 60 48 39 c3 74 50 48 b8 00
[ 6.298698] RSP: 0018:ffff88806c907be8 EFLAGS: 00010206
[ 6.298701] RAX: dffffc0000000000 RBX: ffff888006116800 RCX: 0000000000000020
[ 6.298702] RDX: 000000000000000c RSI: ffff88800525d578 RDI: 0000000000000060
[ 6.298703] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 6.298706] R10: 0000000000000020 R11: 0000000000000000 R12: 0000000000000000
[ 6.298706] R13: 000000000000002e R14: ffff8880056eb440 R15: ffff888006116800
[ 6.298707] FS: 00007fc02d1c2740(0000) GS:ffff8880b29bc000(0000) knlGS:0000000000000000
[ 6.298710] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6.298711] CR2: 000055fe3b56ddf8 CR3: 00000000053b9004 CR4: 0000000000770ef0
[ 6.298712] PKRU: 55555554
[ 6.298713] Call Trace:
[ 6.298714]
[ 6.298714] __iscsi_complete_pdu+0x13a8/0x22a0
[ 6.298758] iscsi_complete_pdu+0x54/0xa0
[ 6.298759] iscsi_tcp_hdr_recv_done+0x870/0x2c80
[ 6.298778] iscsi_tcp_recv_skb+0x31e/0xec0
[ 6.298800] iscsi_sw_tcp_recv+0x12f/0x390
[ 6.298804] __tcp_read_sock+0x1ab/0x810
[ 6.298812] iscsi_sw_tcp_data_ready+0x18b/0x510
[ 6.298814] tcp_rcv_established+0x1f56/0x3a00
[ 6.298842] tcp_v4_do_rcv+0x449/0x960
[ 6.298847] tcp_v4_rcv+0x2245/0x3bc0
-
CVE-2026-99147
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
drm/exec: don't immediately add prelocked obj to array of locked objs
When a contention is detected the drm_exec object grabs a reference to
the contended object, unlocks all other objects and pre-locks the
contended one before anything else.
The problem is that it is possible that this pre-locked object was about
to be destroyed and drm_exec is now holding the last reference to it.
So we never actually see this pre-locked object again to be explicitly
locked and so also never reserve a slot for a dma_fence object on it.
Should the driver now use drm_exec_for_each_locked_object() to add a new
fence to all locked objects we eventually see a warning or even a
BUG_ON() to prevent random memory corruption.
Fix this by keeping the prelocked object out of the array of locked objs
until it was explicitly mentioned by the driver again.
If the prelocked object is never mentioned again by the driver
just unlock and drop the reference at the end of the locking loop.
-
CVE-2026-99144
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix use-after-free of a destroyed user DSQ by a deferred reenqueue
A deferred reenqueue can read a freed user DSQ. The request stays on its
CPU's deferred list until run_deferred() takes it, and the RCU callback that
frees the DSQ assumes that the grace period has flushed it, so exit_dsq()
checks the per-CPU node without the deferred list lock. A grace period waits
for readers in flight, not for a pending run_deferred(). A run_deferred()
which starts after the grace period began can detach the request right
before the callback looks and then read the freed DSQ's id.
Cancel the pending requests before the grace period instead. The irq work
that frees the DSQ unlinks every CPU's request under the per-CPU deferred
list lock, and schedule_dsq_reenq() ignores a new request under the same
lock once the id is invalid. Only a run_deferred() that started before the
grace period can hold a request, and it runs with IRQs disabled, so the
grace period waits for it and nothing touches the DSQ after the callback.
-
CVE-2026-99141
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix crash in print_graph_function_event()
tracing_set_tracer() assigns the flags of the newly selected tracer
with:
tr-current_trace_flags = t->flags ? : t->tracer->flags;
If the new tracer defines neither static flags nor default flags, like
hwlat, irqsoff or wakeup, add_tracer() has no per instance flags copy
for it, and both operands are NULL, so tr->current_trace_flags ends up
being NULL as well.
The ring buffer is not cleared when switching tracers: it is reset
inside tracer_init(), after current_trace_flags was already assigned.
If the buffer still holds function_graph entries of the previous
tracer, printing one of them dereferences the NULL pointer. This was
hit by cat trace during an ftrace stress test:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
RIP: 0010:print_graph_function_event+0xe/0x20
Call Trace:
s_show+0x4d/0x110
seq_read_iter+0x2d4/0x490
seq_read+0x130/0x170
vfs_read+0xb5/0x370
ksys_read+0x6d/0xe0
do_syscall_64+0xbc/0x450
The snapshot buffer is not reset at all, so this can be reproduced
without a race:
echo function_graph > /sys/kernel/tracing/current_tracer
echo 1 > /sys/kernel/tracing/snapshot
echo hwlat > /sys/kernel/tracing/current_tracer
cat /sys/kernel/tracing/snapshot
Rather than teaching every user of tr->current_trace_flags about this
corner case, make sure it is never NULL: when the newly selected
tracer has no flags at all, tracing_set_tracer() falls back to a
static empty no_tracer_flags. run_tracer_selftest() can hit the same
case, so the same fallback is added there too. The existing users
already handle opts == NULL, so these tracers keep behaving as before.
-
CVE-2026-99139
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
tcp: fix use-after-free in do_tcp_getsockopt(TCP_CONGESTION)
do_tcp_getsockopt() reads icsk-icsk_ca_ops->name without holding
rcu_read_lock(). Since commit 0baf26b0fcd7 ("bpf: tcp: Support
tcp_congestion_ops in bpf"), icsk_ca_ops can point to dynamically
allocated BPF struct_ops memory that may be freed concurrently via
setsockopt(TCP_CONGESTION), leading to a use-after-free.
BUG: KASAN: slab-use-after-free in _copy_to_user+0x37/0x60
Read of size 16 at addr ffff888013505260 by task exploit/149
_copy_to_user+0x37/0x60
do_tcp_getsockopt+0x158a/0x2460 (net/ipv4/tcp.c:4585)
tcp_getsockopt+0x91/0xf0
__sys_getsockopt+0xf7/0x170
Fix this by holding rcu_read_lock() around the ca_ops->name access,
using READ_ONCE() to load icsk_ca_ops, and copying the name to a
stack buffer before releasing the lock. Also annotate the relevant
icsk_ca_ops stores with WRITE_ONCE() to fix the accompanying KCSAN
data-race issue.
-
CVE-2026-99136
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
dm-crypt: fix a tiny race condition in crypt_dec_pending
crypt_dec_pending reads io-error before calling atomic_dec_and_test.
Another context, for example crypt_endio called from an interrupt, may
set io->error and drop its reference between the read and the
decrement. crypt_dec_pending then drops the last reference and completes
the bio with the stale status - so a read that failed and was never
decrypted, or a write that failed, is reported as successful.
The read was placed before the decrement by commit b35f8caa0890 ("dm
crypt: wait for endio to complete before destruction"), because that
commit freed dm_crypt_io before calling bio_endio. This is no longer the
case, dm_crypt_io lives in the per-bio data now.
Read io->error after atomic_dec_and_test instead. atomic_dec_and_test is
fully ordered, so no additional barrier is needed.
-
CVE-2026-99134
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
mac802154: fix data race and NULL deref on local-assoc_dev
local->assoc_dev is shared between the association path and the
association-response worker without common synchronization.
mac802154_perform_association() stores the coordinator pointer and waits
for a response. Its timeout and error paths clear the pointer and return
to mac802154_associate(), which may then free the coordinator object.
Meanwhile, mac802154_rx_mac_cmd_worker() may observe the associating bit
and enter mac802154_process_association_resp(), which dereferences
assoc_dev.
The worker's bit test and the handler's pointer dereference are not
atomic with respect to cleanup. Cleanup can clear assoc_dev between them,
causing a NULL dereference, or free the coordinator while the response
handler still uses the pointer.
The recorded result is exposed to the same window. assoc_status and
assoc_addr are written by the handler but read by the association path
while the associating bit is still set, so a second response for the same
request - a malicious one, for instance - can replace them between those
reads and leave the caller with an incoherent status and address pair.
The response handler only needs the coordinator extended address.
Replace assoc_dev with a cached address, removing the pointer lifetime
dependency. Protect the cached address and the associating bit with a
dedicated spinlock. A READ_ONCE()/WRITE_ONCE() pair would not guarantee
an atomic __le64 access on all 32-bit architectures.
wpan_dev->association_lock cannot be reused here: nl802154_associate()
holds it across rdev_associate(), hence for the whole of
mac802154_perform_association() including the wait for the response.
A response handler taking that lock would only get it once the
association has already given up.
Reset the completion, publish the cached address, and set the associating
bit while holding the lock. The response handler takes the lock, rechecks
the bit and the cached address, records the response, clears the bit, and
only then completes the waiter. Thus cleanup cannot pass the handler
between its state check and completion, and the cached 64-bit value
cannot tear.
The handler clears the bit before completing, not the woken waiter:
otherwise complete() is issued under the lock and a second (e.g.
malicious) response can reacquire it before the waiter and replace the
result. So a wait that returns success implies the bit is already clear,
and the success and negative-response paths return directly. The
transmit-error and timeout paths still clear it under assoc_lock, which
serializes any racing response against the cleanup while the call returns
the error it already selected. Both paths snapshot assoc_status and
assoc_addr under the same lock.
Both users run in process context, so a plain spinlock is sufficient.
The lock is not held while waiting for the completion.
-
CVE-2026-99133
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
net/iucv: fix the recvmsg window update
iucv_sock_recvmsg() sends the HiperSockets-only AF_IUCV_FLAG_WIN without
testing the transport, so on a classic z/VM socket iucv_send_ctrl() sizes
the skb through a NULL iucv-hs_dev. SO_MSGLIMIT accepts 1, so msglimit / 2
is zero and one recvmsg() on its own socket is enough for an unprivileged
process to take a spurious disconnect.
It also calls iucv_send_ctrl() under spin_lock_bh(&message_q.lock), which
allocates GFP_KERNEL inside a section the code treats as atomic. Sending
outside that lock lets two recvmsg() reach afiucv_hs_send() at once, where
msg_recv is sampled for the advertised window and subtracted after
dev_queue_xmit() -- and sendmsg reaches that counter under lock_sock()
while recvmsg holds no socket lock, so both can subtract the same value,
the counter goes negative and the credit reaches the peer twice.
Test the transport, claim the credit with atomic_xchg() after the last
error exit and hand it back if the transmit fails, and send once the lock
is dropped.
-
CVE-2026-99131
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
xfs: fix capability check in xfs
An user reported a bug where he managed to evade group's quota
by changing a file's gid to a different group id the same user
belonged to, even though quotas were enforced on both gids and the
file's size was big enough to exceed the quota's hardlimit.
Commit eba0549bc7d1 replaced a capable() call by a
has_capability_noaudit() to prevent unnecessary selinux audit messages.
Turns out that both calls have slightly different semantics even though
their documentation seems similar. Where in a nutshell:
capable() - Tests the task's effective credentials
has_ns_capability_noaudit() - Tests the task's real credentials
This most of the time has no practical difference but in some cases like
changing attrs (specifically group id in this case) through a NFS client
this will allow the quota code to use XFS_QMOPT_FORCE_RES, effectively
bypassing quota accounting checks.
Using instead ns_capable_noaudit() should fix this issue and prevent
selinux audit messages.
This also fix the remaining calls to has_capability_noaudit()
-
CVE-2026-99130
•
published on October 28, 2026
In the Linux kernel, the following vulnerability has been resolved:
io_uring/cancel: don't spin on local work the task can't run
io_uring_cancel_generic() refuses to sleep while any ring on the exiting
task's tctx has local work pending. It assumes the task is that ring's
submitter and that the next io_uring_try_cancel_requests() pass will run
the work. This does not hold for a ring that was still
IORING_SETUP_R_DISABLED when the task got its tctx node from
io_uring_create() or io_ringfd_register(). The submitter is set later by
IORING_REGISTER_ENABLE_RINGS, possibly from another task, and only the
submitter may run local work on an IORING_SETUP_DEFER_TASKRUN ring. To
the exiting task the work stays pending forever, the loop never reaches
schedule(), and the task trips the WARN_ON_ONCE() once and then spins in
do_exit().
An unprivileged user can set this up at will by creating a disabled
ring, having a child enable it and stop, posting to the ring with
IORING_OP_MSG_RING and exiting with a request in flight that only the
child can complete. The exiting thread burns a CPU until the child runs
or dies, and with panic_on_warn set the WARN panics the kernel.
Fix by skipping the sleep only when io_allowed_defer_tw_run() allows the
task to run the work. This is reasonable since work it cannot run cannot
complete any of its requests either, so nothing is lost by sleeping.
Drop the WARN_ON_ONCE() since handing a disabled ring to another thread
is a supported scenario, not a bug state.