-
CVE-2026-98761
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: recover after failure to start the frs ams
Reset the port if the tcpm fails to start the FAST_ROLE_SWAP AMS by
initiating error recovery on it.
This helps in cases where some cables (incorrectly) signal an FRS to
an FRS capable port during disconnection. The TCPC autonomously starts
sourcing VBUS on detecting the FRS signal. However, the VBUS sourcing is
left on when the FAST_ROLE_SWAP AMS fails to start (as tcpm_sink_tx_ok
is 0 as CC is open due to the cable disconnect). This is because the
code sets the state to INVALID_STATE without resetting the port state.
Log snippet before changes:
[ 101.401960] AMS FAST_ROLE_SWAP start
[ 101.401971] Sink TX No Go
[ 101.401982] sourcing vbus
[ 101.401987] VBUS on
[ 101.402159] VBUS on
[ 109.257809] CC1: 0 - 0, CC2: 5 -> 0 [state SNK_READY, polarity 1, disconnected]
[ 111.267442] VBUS on
After changes:
[ 70.541211] AMS FAST_ROLE_SWAP start
[ 70.541220] Sink TX No Go
[ 70.541228] state change SNK_READY -> ERROR_RECOVERY [rev3 NONE_AMS]
[ 70.541362] VBUS on
[ 70.541365] sourcing vbus
[ 70.541367] VBUS on
[ 70.541374] state change ERROR_RECOVERY -> PORT_RESET [rev3 NONE_AMS]
[ 70.541410] disable vbus discharge ret:0
[ 70.543028] Setting usb_comm capable false
[ 70.544009] Setting voltage/current limit 0 mV 0 mA
[ 70.544034] polarity 0
[ 70.544239] Requesting mux state 0, usb-role 0, orientation 0
[ 70.555550] cc:=0
[ 70.555595] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[ 70.555697] VBUS off
[ 70.555702] VBUS VSAFE0V
[ 70.555762] CC1: 5 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 70.587794] VBUS off
[ 70.587799] VBUS VSAFE0V
[ 70.655672] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 70.655682] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 70.655686] Start toggling
[ 70.656274] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
-
CVE-2026-98758
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: glink: fix use-after-free of ucsi on remove
The pmic_glink client is released by the devres cleanup, which runs
after pmic_glink_ucsi_remove() has returned, so its notification
callbacks can queue work until then. Work that runs after
ucsi_unregister() has been called touches freed state: it dereferences
the connector array that ucsi_unregister() freed, or registers and
unregisters the instance a second time.
Disable both work items with disable_work_sync() before unregistering,
and unregister only if the instance is still registered.
This issue was found by an in-house static analysis tool.
-
CVE-2026-98756
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
usb: cdns3: Fix NULL pointer dereference in cdns3_pci_probe
The Cadence USBSS controller is a two-function PCI device. The first
probed function allocates the driver data and stores it with
pci_set_drvdata(), while the second function reuses it via
pci_get_drvdata() when pci_is_enabled() reports that the first
function has already been probed.
When the second function is probed while the first one has been
enabled but has not yet set its driver data, pci_get_drvdata()
returns NULL, and the subsequent wrap-devfn assignment dereferences
a NULL pointer and crashes the kernel.
logs:
Call trace:
cdns3_pci_probe+0xa4/0x300
local_pci_probe+0x44/0xa8
pci_call_probe+0x54/0x158
pci_device_probe+0x84/0x100
really_probe+0x184/0x3d0
__driver_probe_device+0x80/0x178
driver_probe_device+0x44/0xe8
__driver_attach+0xec/0x1f8
bus_for_each_dev+0x7c/0xe0
driver_attach+0x28/0x38
bus_add_driver+0x110/0x238
driver_register+0x64/0x128
__pci_register_driver+0x50/0x60
cdns3_pci_driver_init+0x28/0x38
do_one_initcall+0x5c/0x280
do_initcalls+0x104/0x1d8
kernel_init_freeable+0x140/0x218
kernel_init+0x28/0x1f8
ret_from_fork+0x10/0x20
Return -EPROBE_DEFER in this case so that probing is retried after
the first function has completed its probe.
-
CVE-2026-98755
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
tty: vcc: zero-initialize control packet in vcc_send_ctl()
The stack-allocated struct vio_vcc pkt was partially initialized,
leaving the tag.stype_env field uninitialized before being sent via
ldc_write(), potentially leaking kernel stack data to the LDC peer.
-
CVE-2026-98746
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
serial: ma35d1: Fix clock reference leak in ma35d1serial_probe()
of_clk_get() returns a clock with a reference that has to be released
with clk_put(). ma35d1serial_probe() never does that, so the reference
is leaked on the probe error paths and also when the port is removed.
Release it on the error paths and in ma35d1serial_remove().
-
CVE-2026-98744
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: max98363: fix uninitialized stream_config-type
stream_config is not initialized before being passed to
sdw_stream_add_slave(). The type field may contain garbage and is
later copied to stream->type by sdw_config_stream().
Zero-initialize stream_config so type defaults to SDW_STREAM_PCM.
-
CVE-2026-98733
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize fragmented ISO packet queueing
The fragmented path in hci_queue_iso() calls __skb_queue_tail() without
holding conn-data_q.lock. The socket lock serializes senders, but the
transmit worker can concurrently remove packets from this queue using
skb_dequeue().
After an insertion saves the old tail pointer, hci_sched_iso() can dequeue
that packet and pass it to the driver. The driver can free the packet
before the insertion resumes and writes to the old tail's next pointer,
causing a use-after-free. Concurrent updates can also corrupt the queue.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_send_iso+0xc7d/0xe10
Call Trace:
hci_send_iso+0xc7d/0xe10
iso_sock_sendmsg+0x710/0x900
__sys_sendto+0x34a/0x3a0
Allocated by task 86:
__alloc_skb+0xdd/0x820
alloc_skb_with_frags+0x7e/0x770
sock_alloc_send_pskb+0x67a/0x820
bt_skb_sendmsg.constprop.0+0xc0/0x6c0
iso_sock_sendmsg+0x44e/0x900
Freed by task 90:
kmem_cache_free+0xcb/0x3d0
vhci_read+0x33f/0x4d0
vfs_read+0x177/0xa20
Hold the queue lock across the entire fragment batch, as hci_queue_acl()
does, to serialize insertion against dequeue while preserving fragment
ordering.
-
CVE-2026-98731
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: fix plen overflow in btintel_pcie_recv_frame()
plen is u16 and computed as HDR_SIZE + dlen. For ACL/ISO frames dlen
is a 16-bit field, so a value = 0xFFFC wraps the sum, bypassing the
"skb->len plen" check and letting skb_trim() truncate the packet.
Widen plen to u32 so the addition cannot wrap.
-
CVE-2026-98726
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
nvme-multipath: fix underflow in ANA log bounds checks
The number of ANA groups advertised through Identify Controller sizes the
ANA log buffer. The ANA log header and group descriptors independently
supply the number of groups and namespace IDs to parse.
Both bounds checks subtract an untrusted object size from ana_log_size
before comparing the current offset. If the object is larger than the
buffer, the size_t subtraction underflows and lets the parser read beyond
ana_log_buf.
Check the current offset before the first subtraction and compare each
object size with the remaining buffer instead. This rejects inconsistent
ANA data before dereferencing a truncated group descriptor or walking an
oversized namespace ID array.
-
CVE-2026-98724
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
nvmet: pci-epf: reject too-short SGL segments
The host controls an SGL segment's length. A nonzero length smaller than
one SGL descriptor makes nr_descs zero, so
nvmet_pci_epf_get_sgl_segment() reads the type byte of sgls[-1] outside
the allocated buffer. If that byte contains a segment descriptor type,
the function also copies the preceding 16 bytes and returns a negative
descriptor count.
The read was reproduced in 3/3 KASAN boots with only the host transfer
mocked by a KUnit test:
BUG: KASAN: slab-out-of-bounds in nvmet_pci_epf_get_sgl_segment
Read of size 1 by task kunit_try_catch
Call Trace:
nvmet_pci_epf_get_sgl_segment
nvmet_pci_epf_short_sgl_test
Kernel panic - not syncing: KASAN: panic_on_warn set ...
Reject segments that cannot hold one descriptor before allocating or
transferring their contents.
-
CVE-2026-98718
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Do cache maintenance on the source VM *before* clearing SEV state
Explicitly flush caches after intra-host migration before clearing "SEV
active" on the source VM, as doing cache maintenance afterwards creates a
tiny window where memory reclaim could return memory to the host without
performing a cache flush, e.g. as pointed out by Sashiko:
CPU1 in sev_migrate_from():
src-active = false;
CPU2 running concurrent unmap:
Since active is false, the automatic cache flush in
sev_guest_memory_reclaimed is skipped.
The host frees and reallocates the page.
CPU1 in sev_migrate_from():
sev_writeback_caches(src_kvm);
Executes a hardware cache flush (wbnoinvd), which writes the guest's old
dirty ciphertext over the new page owner's data.
-
CVE-2026-98714
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Update control fields on #VMEXIT if and only if VMRUN succeeded
Leave control.erap_ctl and control.clean as-is in the VMCS if VMRUN fails,
because as per AMD:
there's no explicit architectural guarantee about the behavior in the
presence of VMRUN failures. So the best thing to do would be to assume
that if VMRUN fails, the actions requested in the control fields may not
have been performed.
-
CVE-2026-98711
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: cw1200: fix TX padding OOB read leaking heap data to device
The TX path rounds the transfer size up to the bus alignment
(align_size(), up to 511 bytes for SDIO, 1 byte for SPI) but sends
the padded length straight from the frame buffer, which has no room
reserved for the padding. cw1200_data_write() therefore reads past
the end of the frame and the bus transfer carries those bytes to the
device. A bogus device can collect up to 511 bytes of kernel heap
data per TX frame.
The RX path does not have this problem: it allocates the skb with
the aligned length (alloc_len) before reading.
Compute the exact padding with the bus align_size() callback, make
sure queued TX frames have tailroom for it, and zero the padding
bytes before the transfer so nothing past the frame is exposed.
This is not expected to change driver behavior on most cases: frame
contents and transfer sizes are unchanged, only the content of the
padding bytes (previously undefined stale memory, now zero), which
the device never reads since the WSM header carries the real frame
length. The skb expansion can only fail under memory exhaustion,
in which case the frame is dropped like on the existing error paths
of cw1200_tx().
Discovered by Atuin - Automated Vulnerability Discovery Engine.
-
CVE-2026-98707
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: shut down RX BA session timer on teardown
Tearing down an RX BA session can leave the session timer queued on a
freed tid_rx. Later timer-wheel processing and the timer callback itself
then run against freed memory.
An RX BAR handler can dereference tid_rx under RCU before teardown
unpublishes it and stay in its read-side critical section while teardown
deletes the session timer. The stale handler can then rearm the timer
after timer_delete_sync() returns and before the RCU callback frees
tid_rx.
Use timer_shutdown_sync() so rearm attempts become ineffective once
teardown starts. Keep reorder_timer unchanged: teardown marks the session
removed under reorder_lock and its release path checks that state before
rearming. session_timer has no equivalent guard because
ieee80211_rx_h_ctrl() rearms it before taking reorder_lock.
-
CVE-2026-98705
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: account proxy paths against the mesh path limit
Proxy-path churn can drive the interface path counter negative and let
later mesh path additions exceed MESH_MAX_MPATHS.
mesh_path_free_rcu() decrements the interface mpaths counter for entries
from both the mesh and proxy path tables, but mpp_path_add() never
reserves a slot in that counter. Removing or expiring a proxy path
therefore returns a slot that was never charged.
mesh_path_add() uses the same counter to enforce MESH_MAX_MPATHS, so once
it falls below the number of installed paths the limit no longer holds.
Reserve the shared quota before allocating a proxy path and release it on
every unsuccessful addition. Mesh and proxy paths now share one
1024-entry budget, so mpp_path_add() can return -ENOSPC at that limit.
-
CVE-2026-98704
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: keep fallback association elements alive
Associating to a non-transmitted MBSSID profile reads freed memory while
determining the operating channel and applying HT capabilities.
When an association response omits WMM, HT, or VHT information,
ieee80211_assoc_config_link() parses the cached BSS IEs and copies the
missing element pointers out of that fallback parse. For a
non-transmitted MBSSID profile those pointers refer to merged-profile
storage owned by the parse object, and the fallback block frees that
object at its end. The copied pointers are used afterwards to determine
the operating channel, configure bandwidth, and apply HT capabilities.
Keep the fallback parse result alive until association setup finishes.
[reorder variable declaration]
-
CVE-2026-98699
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: fix mesh fast xmit path deletion UAF
mesh_fast_tx_cache() stores raw mesh_path pointers. Path deletion
flushes the cache and then frees the path with kfree_rcu(), but a
lookup that already holds the path can insert a new cache entry
after the flush. The cache then points at freed memory.
Set MESH_PATH_DELETED before flushing, and skip inserting a cache
entry if the path or MPP path is already deleted. Check this under
the cache walk lock so it is ordered with the flush. Use WRITE_ONCE()
for the deletion flag updates because the cache check reads flags
without taking state_lock.
-
CVE-2026-98692
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Make the DP tunnel activation callback mandatory
tb_tunnel_alloc_dp() takes an optional callback which is run from
dprx_work once the DPRX capabilities read has completed. Without that
callback tb_dp_dprx_start() reads the capabilities synchronously and
never queues the work. It however always takes a tunnel reference which
is only dropped by dprx_work itself or by tb_dp_dprx_stop() when
cancel_delayed_work() actually canceled that work. That reference is
thus leaked for every tunnel without a callback.
The only tunnels without one are those from tb_tunnel_discover_dp(),
which are activated again when restoring from hibernation.
Pass the callback to tb_tunnel_discover_dp() as well and drop the
synchronous path such that the DPRX capabilities are always read from
dprx_work. Hibernation restore then also no longer blocks for up to 12
seconds while waiting for that read to complete.
Also fix up the KUnit tests.
-
CVE-2026-98690
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix domain reference leak when DPRX read is canceled
tb_tunnel_one_dp() takes a domain reference which is only dropped once
tb_dp_tunnel_active() has run on the work queue. If that work is
cancelled that reference is leaked. Since
commit f5cc545f5969 ("thunderbolt: Wait for tb_domain_release() to
complete when driver is removed") instead of just leaking memory this
now also blocks in the completion wait forever when unbinding the
driver.
This can be triggered whenever a DP tunnel is torn down before the DPRX
read has completed, e.g. by unplugging within the timeout, and then
unbinding the driver.
That reference only exists to keep the domain around while the DPRX work
is scheduled so let the work itself own it: take it in tb_dp_dprx_start()
and drop it in both places that end the work. Get/put are then paired
inside the same file and it doesn't matter anymore if the callback ever
runs.
-
CVE-2026-98688
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix NULL dereference in tb_remove_work()
There is a slight race between tb_remove_work() and tb_domain_remove()
which leads to dereferencing a NULL tb-root_switch pointer inside
tb_free_unplugged_xdomains():
Thread A Thread B
tb_remove_work()
tb_domain_remove()
mutex_lock(&tb->lock)
tb_stop()
/* doesn't cancel a running callback */
cancel_delayed_work(&tcm->remove_work)
...
tb_switch_remove(tb->root_switch)
tb->root_switch = NULL
mutex_unlock(&tb->lock)
mutex_lock(&tb->lock)
...
/* without checking ->root_switch */
tb_free_unplugged_xdomains(tb->root_switch)
mutex_unlock(&tb->lock)
Commit a8937f35cf39 ("thunderbolt: Remove XDomain from the bus without
holding tb->lock") doesn't seem right to move tb_free_unplugged_xdomains()
out of the &tb->lock section and the check for tb->root_switch, in
particular. It states:
For this reason separate removing the XDomain from the topology data
structures (where we need the lock) from unregistering the device from
the bus (where remove callbacks of the drivers are being called).
tb_free_unplugged_xdomains() belongs to the former group of functions
requiring the lock. And it also calls tb_xdomain_remove() which should
only be called with &tb->lock held.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool.