-
CVE-2026-98620
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk_eth_soc: unregister net_devices in case of probe failure
If register_netdev() fails for one of the MTK_MAX_DEVS devices in
mtk_probe(), the error path jumps to err_deinit_ppe, skipping
mtk_unreg_dev(). The previously registered net_devices are then freed by
mtk_free_dev() while still in NETREG_REGISTERED state, hitting the
BUG_ON(dev-reg_state != NETREG_UNREGISTERED).
Route the register_netdev() failure to err_unreg_netdev so the net_devices
registered so far are properly unregistered before being freed.
-
CVE-2026-98615
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
eth: fbnic: Set AW_FLUSH_MODE alongside AW_FLUSH when flushing the mailbox
When tearing down the FW mailbox Rx ring, fbnic_mbx_reset_desc_ring()
writes AW_CFG with FLUSH set and everything else, BME included, cleared.
Clearing BME halts the device's writes to the host but leaves the staged
requests parked in the PUL write pipeline rather than draining them, so
on the write path FLUSH alone never terminates the outstanding requests
and the flush the firmware waits on never completes.
Add the FLUSH_MODE definition and set both bits so the staged writes
drain out of the pipeline on their own. BME stays cleared, so nothing
lands on the host; it is restored later in fbnic_mbx_init_desc_ring()
when the ring is rebuilt, once the outstanding writes are gone.
The read path is unaffected. AR_CFG has no equivalent mode bit and
AR_FLUSH terminates the outstanding reads by itself, so it is left as
is.
Both writes remain plain stores rather than read-modify-writes. That is
deliberate: the matching write in fbnic_mbx_init_desc_ring() restores
BME and the TLP attributes, and clears both flush bits as a side effect.
-
CVE-2026-98609
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
drm/virtio: fix object leak when drm_gem_handle_create() fails
virtio_gpu_gem_create() owns the reference taken by
virtio_gpu_object_create(). On the drm_gem_handle_create() error path it
calls drm_gem_object_release() instead of dropping that reference.
drm_gem_object_release() is the inverse of drm_gem_object_init() and does
not touch the reference count or call obj-funcs->free(), so it is only
correct as the last step of a destructor, as in
virtio_gpu_cleanup_object(). Using it here leaves the bo at refcount 1
with no remaining reference, so virtio_gpu_free_object() never runs and
the shmem pages, sg table and virtio_gpu_object are leaked. Since
virtio_gpu_object_create() has already set bo->created,
VIRTIO_GPU_CMD_RESOURCE_UNREF is not queued either, leaking the host-side
resource and the resource id.
drm_gem_handle_create_tail() drops the handle reference on all of its
internal error paths, so the caller only has to drop its own. Use
drm_gem_object_put(), matching the success path below.
-
CVE-2026-98601
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel_pcie: validate device-supplied DMA indices
In btintel_pcie_msix_rx_handle(), the driver processes RX completion
descriptors (urbd1) written by the PCIe device into DMA-coherent memory.
urbd1-frbd_tag (a 16-bit field fully controlled by the device firmware
via DMA) is used directly as an array index into rxq->bufs[] without any
bounds check. rxq->bufs[] has only BTINTEL_PCIE_RX_DESCS_COUNT (64)
entries, while frbd_tag can be any value 0-65535. A malicious or
malfunctioning device can write an out-of-range frbd_tag, causing the
driver to dereference an out-of-bounds data_buf pointer.
Additionally, cr_hia is read from a DMA-shared index array also writable
by the device; if the device sets cr_hia >= rxq->count, the while-loop
never terminates because cr_tia is wrapped via modulo rxq->count and can
never equal an out-of-range cr_hia.
Add bounds validation for cr_hia and frbd_tag in the RX path, and cr_hia
in the TX path. Log invalid values with bt_dev_err before returning.
-
CVE-2026-98600
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Reject short EA=0 frames in rfcomm_recv_frame()
While rfcomm_recv_frame() verifies that skb-len is at least
sizeof(*hdr) + 1 (4 bytes: 3-byte header + 1-byte FCS), an RFCOMM frame
with an extended 2-byte length field (!__test_ea(hdr->len)) has a 4-byte
header plus a 1-byte FCS (5 bytes minimum, sizeof(*hdr) + 2).
When a 4-byte RFCOMM frame with EA == 0 arrives:
1. The initial skb->len sizeof(*hdr) + 1 check passes (4 < 4 is false).
2. Trimming the FCS byte decrements skb->len to 3.
3. If __check_fcs() succeeds, skb_pull(skb, 4) fails (4 > 3) and returns
NULL without advancing skb->data.
4. Because the return value of skb_pull() is ignored, the un-pulled
3-byte struct rfcomm_hdr remains at skb->data and is either queued as
application payload via rfcomm_recv_data() or parsed as a multiplexer
control command via rfcomm_recv_mcc() on DLCI 0.
Fix this by extending the length check in rfcomm_recv_frame() to also
require skb->len >= sizeof(*hdr) + 2 when !__test_ea(hdr->len).
-
CVE-2026-98597
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: usb: sr9700: include receive overhead in the length check
The receive fixup subtracts the Ethernet CRC from the reported packet
length, but compares that payload length against the whole remaining
receive buffer. The following copy starts after the three-byte header,
and the cursor advance consumes both that header and the four-byte CRC.
Require the payload to fit after SR_RX_OVERHEAD before copying it or
advancing to the next packet. The loop already ensures that the
remaining buffer is larger than the overhead, so the subtraction is
safe.
The issue was found by our static-analysis tool.
-
CVE-2026-98596
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
ipv6: Fix dst leak for uncached routes.
ip6_route_output_flags(), ip6_rt_put_flags(), and ip6_dst_check()
detect an uncached route by list_empty(&rt-dst.rt_uncached),
which replaced the static DST_NOCACHE flag check in commit
a4c2fd7f7891 ("net: remove DST_NOCACHE flag").
When a device is unregistered, rt6_uncached_list_flush_dev()
unlinks uncached routes tied to the device from rt6_uncached_list.
Previously, they were moved to another list with list_move()
(__list_del_entry() + list_add()), and since commit 98aa546af5e4
("inet: remove (struct uncached_list)->quarantine"), the routes
are just unlinked with list_del_init().
If list_del_init() runs concurrently, list_empty() evaluates to
true; ip6_route_output_flags() calls dst_hold_safe() incorrectly
and ip6_rt_put_flags() skips ip6_rt_put(), leaking dst, and thus
dev tied via rt->from as well.
The same race is partially fixed by commit 9a6f0c4d5796 ("dst:
fix races in rt6_uncached_list_del() and rt_del_uncached_list()").
Let's check rt6->dst.rt_uncached_list instead.
Note that IPv4 does not have the same issue.
-
CVE-2026-98589
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject pkt arguments in mutating subprogs
The verifier tracks changes in how PTR_TO_PACKET registers'
bounds are modified across subprog boundaries. PTR_TO_PACKET
registers are actually passed as PTR_TO_MEM, which is assumed
valid for the entire call. This is not the case with packet memory,
where a pskb_* call may invalidate its memory region.
Reject BPF code that passes PTR_TO_PACKET pointers to subprogs that
may mutate a packet. We cannot pass the pointer as a true PTR_TO_PACKET
because we would also need to somehow pass the PTR_TO_PACKET_META
or PTR_TO_PACKET_END to the subprog. Since we cannot avoid representing
the pointer in the subprog as PTR_TO_MEM, only permit it if the
subprog is guaranteed not to mutate the packet.
-
CVE-2026-98581
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix list corruption / refcount desync in nfc_llcp_recv_dm()
nfc_llcp_recv_dm() handles DM(NOBOUND)/DM(REJ) for a socket that is still
linked on local-connecting_sockets: it looks the socket up with
nfc_llcp_connecting_sock_get(), sets sk->sk_state = LLCP_CLOSED and
returns, without taking the socket lock and without unlinking the socket
from the connecting_sockets list.
llcp_sock_release() selects the list to unlink from by sk_state: a socket
in LLCP_CONNECTING is unlinked from connecting_sockets, otherwise from the
sockets list. Because recv_dm left the socket physically on
connecting_sockets but in the LLCP_CLOSED state, release() takes the else
branch and calls nfc_llcp_sock_unlink(&local->sockets, sk). That runs
sk_del_node_init() while holding sockets.lock, i.e. it removes the socket
from the connecting_sockets hlist under the wrong lock. A concurrent
connect() linking another socket onto connecting_sockets under
connecting_sockets.lock then mutates the same hlist unserialized, which
corrupts the list and desyncs the sk_add_node()/sk_del_node_init()
sock_hold()/__sock_put() pairing. An unprivileged local process holding
LLCP sockets, with the DM supplied by the remote peer over an established
LLCP link, can drive this to leak kernel sockets without bound (the
mis-decrement goes through the non-freeing __sock_put() path, so the
object is never released), leading to memory exhaustion / DoS.
This is the same class of bug that was fixed in the sibling handler
nfc_llcp_recv_cc() by commit b493ea2765cc ("nfc: llcp: Fix use-after-free
race in nfc_llcp_recv_cc()"); recv_dm did not receive the equivalent fix.
Fix it the same way: take lock_sock(), re-check that the socket is still
hashed (release() may have won the race), and for the NOBOUND/REJ case
unlink it from connecting_sockets before moving it to LLCP_CLOSED. The
unlink drops the connecting_sockets membership reference via
sk_del_node_init(), leaving the socket unhashed, so the later
nfc_llcp_sock_unlink() in llcp_sock_release() becomes a no-op and no
double put occurs.
-
CVE-2026-98580
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix race condition in accept_queue lifecycle
In nfc_llcp_socket_release(), sockets and listener accept queues are
walked under the local sockets rwlock and bh_lock_sock(). However,
bh_lock_sock() does not synchronise against process-context lock_sock()
held by nfc_llcp_accept_dequeue() during accept(). Because
socket_release() does not check sock_owned_by_user(), both paths can
concurrently unlink and release the same child socket, resulting in
use-after-free or a NULL pointer dereference of child-parent in
nfc_llcp_accept_unlink().
Fix this synchronisation race by having nfc_llcp_socket_release() use
process-context lock_sock() instead of bh_lock_sock():
1. Pop sockets from the local sockets list under the write lock using
nfc_llcp_sock_list_pop() so lock_sock() can be acquired without
holding the rwlock.
2. Because lock_sock() can sleep, defer the final release of the
nfc_llcp_local structure to a workqueue (release_work). This avoids
a sleeping-in-atomic bug when the last local reference is dropped
from softirq context. Additionally, hold a single device reference
on local from registration until final destruction.
3. In nfc_llcp_local_get(), use kref_get_unless_zero() to prevent
resurrecting a local object whose teardown has been scheduled.
4. In llcp_sock_accept(), verify that the listener socket state is still
LLCP_LISTEN after waking from schedule_timeout() to prevent hangs if
the listener is closed concurrently.
5. When unlinking unaccepted child sockets during listener release,
unlink them from local->sockets, call sock_orphan(), and drop their
initial sk_alloc creation reference via sock_put().
6. Make nfc_llcp_accept_unlink() idempotent by guarding parent access with
a NULL check.
-
CVE-2026-98578
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
nfc: st21nfca: validate ISO15693 inventory length
The ISO15693 inventory helper removes a two-byte prefix without checking
that it exists, then accepts a one-byte remainder before reading data[1] as
the DSFID.
Require the prefix and at least two remaining bytes before copying the UID
data and reading the DSFID.
-
CVE-2026-98577
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: fix WKS SAP hijacking via prefix match in nfc_llcp_wks_sap()
nfc_llcp_wks_sap() compares only service_name_len bytes, so a short
service_name like "u" matches longer WKS strings like "urn:nfc:sn:snep".
Fix by requiring exact length match before strncmp().
-
CVE-2026-98572
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix immediate JMP JEQ/JNE on MIPS32
An addu instruction was emitted instead of addiu, causing the immediate
value 1 to be interpreted as register $at. This made the comparison
result invalid when the immediate operand was negative. Note that $at
is mapped to BPF_REG_AX, which is used for constant blinding.
Fix the instruction to use the immediate form.
Found with test_bpf on MIPS32r1 emulated by QEMU.
-
CVE-2026-98569
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
ip_gre: Reject enabling collect metadata through changelink
ipgre_netlink_parms() can enable collect_md on an existing GRE, GRETAP
or ERSPAN device. Unlike newlink, changelink does not enforce metadata
tunnel uniqueness. Converting a non-metadata device can therefore
replace the metadata receive entry for another device of the same type
in the same netns. Deleting either device then clears the shared entry,
breaking metadata receive lookup for the surviving device.
If parameter validation fails after collect_md is set, deleting the
modified device can also clear an entry it never owned.
Reject enabling metadata mode in both changelink callbacks before any
encapsulation or tunnel parameters are modified. Allow requests that
repeat the metadata attribute on an existing metadata device.
-
CVE-2026-98565
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mt7530: fix NULL dereference on unbind of MT7531 and MT7621
The core and io supplies are only requested for ID_MT7530: both the
devm_regulator_get() in probe and the regulator_enable() in
mt7530_setup() are guarded by the switch id, but mt7530_remove()
disables them unconditionally. On an MT7621 or an MT7531 both pointers
are still NULL from devm_kzalloc(), so rmmod or a sysfs unbind calls
regulator_disable() on NULL.
-
CVE-2026-98562
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: libwx: fix races in Tx timestamp handling
wx-ptp_tx_skb is shared between the Tx path, the PTP auxiliary
worker and the timestamp cleanup paths. The
WX_STATE_PTP_TX_IN_PROGRESS bit prevents multiple Tx paths from
submitting timestamp requests, but does not serialize the worker
against cleanup.
As a result, wx_ptp_clear_tx_timestamp() can free an skb after
wx_ptp_tx_hwtstamp_work() has obtained its pointer. The worker may
then pass the freed skb to skb_tstamp_tx() and release the same
reference again.
The cleanup path may also clear the in-progress bit while the worker
is still processing the old skb. This allows the Tx path to publish a
new skb which the worker can subsequently overwrite with NULL,
leaking its reference.
Add a dedicated spinlock to protect publication and consumption of
the Tx timestamp skb. Detach the skb and clear the in-progress bit
while holding the lock, then deliver the timestamp and release the skb
after dropping it. Use the same locked cleanup in the quiesce path,
but keep the detach there free of register accesses: quiesce runs
during PCIe error recovery, where MMIO is not reliable, and it
deliberately did not touch the device before. The lock is taken with
interrupts disabled, because netpoll can call ndo_start_xmit() with
hard interrupts already off.
When handling a Tx DMA mapping failure, keep the transmit path
reference until after comparing the skb under the lock. This prevents
skb address reuse from making the error path mistake a newer timestamp
request for the failed one.
-
CVE-2026-98556
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
gve: DQO: reject TSO packets with an out of range MSS
gve_prep_tso() notes that the device requires the MSS to be = 9728,
but does not enforce it, assuming the 9K MTU enforced by the hypervisor
and the 64KB limit on TSO sizes are enough.
This does not hold for packets that were not generated locally.
A guest behind a tap, or any packet socket user, can provide an
arbitrary gso_size in virtio_net_hdr. Layer 2 forwarding does not check
the MTU for GSO packets (is_skb_forwardable()), and gso_features_check()
only bounds skb-len and gso_segs, never gso_size.
Such a packet reaches gve_tx_fill_tso_ctx_desc(), which puts gso_size
into the mss field of the TSO context descriptor. This field is 14 bits
wide, so a gso_size of 16384 is silently turned into an MSS of zero.
Drop these packets from gve_prep_tso(), and make sure that
gve_features_check_dqo() leaves their GSO bits alone: skb_segment()
splits at gso_size regardless of the MTU, so falling back to software
segmentation would give the device non TSO packets bigger than the
9728 bytes it supports.
Note that the device can still be given oversized non TSO packets when
the stack segments in software for other reasons, for instance after
TSO has been disabled with ethtool. This is a generic issue, because
the MTU check is skipped for GSO packets in the forwarding path, and
is addressed separately.
-
CVE-2026-98551
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
perf/core: Fill branch entries with a single assignment
perf_clear_branch_entry_bitfields() clears the bitfields of struct
perf_branch_entry one by one and leaves from/to alone, since callers
overwrite those straight away. The list has to be kept in sync with the
struct by hand and has already fallen behind: new_type and priv were
added to perf_branch_entry and never added here.
Only BRBE writes those two, and neither for every record.
brbe_set_perf_entry_type() leaves new_type alone for a branch type it
does not recognise, and priv is not set for source-only records.
arm_pmuv3.c allocates the per-CPU branch stack with kmalloc(), so such a
record reaches userspace with whatever the slot held: uninitialised
kmalloc() data on the first pass over the buffer, the previous record's
values after that. Nothing under arch/x86/events/ writes either field,
so only arm64 is affected.
Assign the whole entry at each site instead. Everything not named is
then zero, and there is no list to keep in sync. The bitfields add up to
exactly 64 bits, so the struct has no padding to leave undefined.
perf_clear_branch_entry_bitfields() has no callers left, so remove it.
perf_entry_from_brbe_regset() assigns an empty literal instead, since it
fills from/to conditionally. PERF_BR_SPEC_NA is 0, so dropping the
explicit spec assignment changes nothing.
-
CVE-2026-98549
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
tcp: prevent collapsing skbs across boundary in rtx queue
tcp_write_collapse_fence() sets TCP_SKB_CB(skb)-eor = 1 on
tcp_write_queue_tail(sk) to prevent skbs queued after a switch to
device encryption from being collapsed into earlier skbs.
The fence is a no-op if all earlier data has already been transmitted
when the switch happens: sk->sk_write_queue is empty. The not yet
acknowledged earlier skbs wait in sk->tcp_rtx_queue with eor 0.
On a subsequent retransmit or SACK shift, tcp_retrans_try_collapse() or
tcp_shift_skb_data() can then merge an skb queued after the switch into
one queued before it.
Both users of the fence are affected:
- psp: devices only encrypt skbs with skb->decrypted set. The merged skb
keeps decrypted = 0 from the earlier skb, so merged data sent after
psp_sock_assoc_set_tx() is retransmitted in cleartext.
- tls device offload: the merged skb straddles the start marker set in
tls_set_device_offload(). The software fallback (fill_sg_in() returns
-EINVAL) and the mlx5, nfp and funeth drivers cannot handle such an
skb and drop it. Every retransmit rebuilds the same skb, so the
connection stalls.
Fix this in two places, for defense in depth:
1. Fall back to tcp_rtx_queue_tail(sk) in tcp_write_collapse_fence()
when tcp_write_queue_tail(sk) is NULL.
2. Check !skb_cmp_decrypted(to, from) in tcp_skb_can_collapse(), as
tcp_skb_can_collapse_rx() does on receive. skb_shift(), which both
collapse paths call, already has a DEBUG_NET_WARN_ON_ONCE() for this
condition.
-
CVE-2026-98548
•
published on October 18, 2026
In the Linux kernel, the following vulnerability has been resolved:
sctp: discard the rest of the packet on a stale-cookie error
When an association is in COOKIE-ECHOED state and the peer sends a
bundled [ERROR(Stale Cookie)][DATA] packet from one of its non-primary
addresses, processing the ERROR chunk takes the non-fatal stale-cookie
retry path sctp_sf_do_5_2_6_stale(), which queues
SCTP_CMD_DEL_NON_PRIMARY while keeping the association alive.
sctp_cmd_del_non_primary() removes every non-primary transport -
including the very transport this packet arrived on, which is still
referenced by the receive lookup and shared by all chunks of the
packet via chunk-transport.
sctp_assoc_rm_peer() does redirect asoc->peer.last_data_from away from
the removed transport, but right afterwards the bundled DATA chunk
makes sctp_assoc_bh_rcv() re-register
asoc->peer.last_data_from = chunk->transport unconditionally, undoing
the redirection with the just-removed transport.
Once the packet is done, the receive reference is dropped and the
transport is RCU-freed, while the surviving association keeps the
dangling last_data_from. A later FWD-TSN (or the delayed SACK timer)
makes sctp_gen_sack() dereference it (->param_flags and friends), and
sctp_make_sack()/sctp_outq_select_transport() may write to the freed
object and link it into the live transport list. This is a
use-after-free triggerable by any malicious SCTP peer (or a local
unprivileged user acting as one) with no capabilities required:
BUG: KASAN: slab-use-after-free in sctp_do_sm+0x498a/0x5660
Read of size 4 at addr ffff88800e1e356c by task poc/115
Call Trace: sctp_do_sm - sctp_assoc_bh_rcv <- sctp_inq_push <-
sctp_rcv <- ip_protocol_deliver_rcu <- ip_rcv
Allocated: sctp_transport_new <- sctp_assoc_add_peer <-
sctp_process_init (INIT-ACK processing)
Freed: kfree <- sctp_transport_destroy_rcu <- rcu_core
(call_rcu queued by sctp_transport_put at end of sctp_rcv)
The buggy address is located 364 bytes inside of freed 1024-byte
region [ffff88800e1e3400, ffff88800e1e3800), cache kmalloc-1k
Note that commit 03a9d10ecf71 ("sctp: drop a chunk if its transport
was removed") only covers the window between the receive lookup and
the chunk processing (e.g. an ASCONF DEL-IP racing the socket backlog);
here the transport is removed *while* the packet is being processed,
by an earlier chunk of the same packet, so the drop in sctp_inq_push()
does not reach this path. Verified with the bundled [ERROR(Stale
Cookie)][DATA] + FWD-TSN reproducer: the KASAN report above still
fires with that commit applied, and is gone with this patch on top.
Fix it by discarding the rest of the packet on this path, as suggested
by Xin. After the stale-cookie ERROR has sent the association back to
COOKIE-WAIT and removed the non-primary transports, the remaining
chunks of the packet can only run against the restarted handshake
while referencing the removed arrival transport through
chunk->transport: besides the last_data_from registration above,
sctp_cmd_setup_t2() and the sctp_make_*() reply builders would also
copy that pointer into association-lifetime state that
sctp_assoc_rm_peer() has already sanitized. Let the peer retransmit
them, in line with what sctp_inq_push() does for chunks whose
transport was removed before processing.