-
CVE-2026-98130
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
sctp: fix a TOCTOU race in SCTP_CMD_TIMER_START
The SCTP_CMD_TIMER_START handler checks timer_pending() before calling
timer_reduce(). The timer can expire and detach between these operations,
causing timer_reduce() to rearm the timer without taking the association
reference required for the newly armed timer.
The timer callback later unconditionally drops its association reference,
which can leave the association reference count unbalanced and result in
use-after-free during association teardown.
Use the return value of timer_reduce() to determine whether the timer was
actually armed. Take the association reference only when timer_reduce()
successfully starts a new timer, closing the race between checking the
timer state and rearming it.
This issue was reported by Nico Yip (@_cyeaa_) working with TrendAI Zero
Day Initiative.
-
CVE-2026-98127
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
smb/client: validate new EOF for insert range
smb3_insert_range() does not check if the new file size
(i_size + len) is valid. This allows FALLOC_FL_INSERT_RANGE to bypass
RLIMIT_FSIZE, exceed s_maxbytes, or produce a size outside the loff_t
range.
Use check_add_overflow() to calculate the new EOF. Validate it with
inode_newsize_ok() before modifying the file.
Reproducer, using a file on a CIFS mount:
bash -c '
FILE=/mnt/cifs/repro
trap "" SIGXFSZ
ulimit -f 3072 # RLIMIT_FSIZE = 3 MiB
# A regular write is stopped at 3 MiB.
dd if=/dev/zero of="$FILE" bs=1M count=4 status=none
stat -c "size after write: %s" "$FILE"
# Insert 2 MiB into a 2 MiB file.
truncate -s 2M "$FILE"
fallocate -i -o 0 -l 2M "$FILE"
stat -c "size after insert: %s" "$FILE"
'
Before this change, the regular write stops at the 3 MiB limit, but
insert range grows the file to 4 MiB:
dd: error writing '/mnt/cifs/repro': File too large
size after write: 3145728
size after insert: 4194304
After this change, insert range also fails at the limit and leaves the
2 MiB file unchanged:
dd: error writing '/mnt/cifs/repro': File too large
size after write: 3145728
fallocate: fallocate failed: File too large
size after insert: 2097152
-
CVE-2026-98126
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
smb/client: validate new EOF for zero range
When FALLOC_FL_ZERO_RANGE is used without FALLOC_FL_KEEP_SIZE,
smb3_zero_range() may extend EOF without checking RLIMIT_FSIZE, allowing
the file to grow beyond the caller's file-size limit.
Fix this by calling inode_newsize_ok() before sending the zero-range
request when the operation would extend EOF.
Reproducer, using a file on a CIFS mount:
bash -c '
FILE=/mnt/cifs/repro
trap "" SIGXFSZ
ulimit -f 3072
truncate -s 2M "$FILE"
fallocate --zero-range -o 0 -l 4M "$FILE"
echo "fallocate rc=$?"
stat -c "file size=%s" "$FILE"
'
Before this change, the operation succeeds despite the 3 MiB limit:
fallocate rc=0
file size=4194304
After this change, fallocate fails and leaves the file at 2 MiB.
-
CVE-2026-98119
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
netfs: break unbuffered write when netfs_alloc_subrequest() fails
syzbot reported a null-ptr-deref below [1] following a fault injection in
netfs_alloc_subrequest(). [0]
When netfs_alloc_subrequest() fails, subreq is NULL.
Later, netfs_prepare_write() tries to initialize members of
subreq(e.g., source), the issue in [1] is triggered.
Let's handle the error of netfs_prepare_write() properly.
[0]
FAULT_INJECTION: forcing a failure.
name failslab, interval 1, probability 0, space 0, times 0
Call Trace:
netfs_alloc_subrequest+0x116/0x3f0
netfs_prepare_write+0x76/0x7b0
netfs_unbuffered_write+0x75c/0x2020
netfs_unbuffered_write_iter_locked+0x7d6/0xa80
netfs_unbuffered_write_iter+0x442/0x720
v9fs_file_write_iter+0xbf/0x100
vfs_write+0x6ac/0x1050
[1]
KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af]
RIP: 0010:netfs_prepare_write+0xbc/0x7b0 fs/netfs/write_issue.c:173
Call Trace:
netfs_unbuffered_write+0x75c/0x2020 fs/netfs/direct_write.c:111
netfs_unbuffered_write_iter_locked+0x7d6/0xa80 fs/netfs/direct_write.c:290
netfs_unbuffered_write_iter+0x442/0x720 fs/netfs/direct_write.c:382
v9fs_file_write_iter+0xbf/0x100 fs/9p/vfs_file.c:409
new_sync_write fs/read_write.c:595 [inline]
-
CVE-2026-98276
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: lock the socket in sock_gettstamp()
sk-sk_flags must only be changed while holding the socket lock,
because sock_set_flag() and sock_reset_flag() use non atomic
operations (__set_bit() and __clear_bit()).
sock_gettstamp() is one of the last places where a bit of sk->sk_flags
is changed from a syscall without owning the socket lock, through
sock_enable_timestamp(sk, SOCK_TIMESTAMP).
sk_set_memalloc() and sk_clear_memalloc() also change sk->sk_flags
without the socket lock, but their callers (nbd, iscsi_tcp, nvme-tcp,
sunrpc, wireguard) need a careful audit, this will be addressed in a
separate patch.
Jungwoo Lee and Wongi Lee reported an UDP socket use-after-free
caused by this bug: a SIOCGSTAMPNS_NEW ioctl racing with bind()
can cancel the SOCK_RCU_FREE bit that udp_lib_get_port() just set,
because both threads perform a read-modify-write on the same word.
CPU 0 (bind) CPU 1 (SIOCGSTAMPNS_NEW)
-------------------------------- ----------------------------
read sk_flags = F read sk_flags = F
compute F | BIT(SOCK_RCU_FREE) compute F | BIT(SOCK_TIMESTAMP)
store F | BIT(SOCK_RCU_FREE)
sk_add_node_rcu(sk, ...)
store F | BIT(SOCK_TIMESTAMP)
After the lost update, SOCK_RCU_FREE is clear while the socket is
visible to lockless UDP receive lookups. sk_destruct() then frees
the socket immediately instead of waiting for a RCU grace period,
while the receive path still holds a reference-less pointer to it:
BUG: KASAN: slab-use-after-free in ipv4_pktinfo_prepare+0x30/0x410
Read of size 8 at addr ffff888008806610 by task exploit/207
CPU: 0 UID: 1000 PID: 207 Comm: exploit Not tainted 6.12.95+ #1
ipv4_pktinfo_prepare+0x30/0x410
udp_queue_rcv_one_skb+0x51c/0x1180
udp_unicast_rcv_skb+0x109/0x350
ip_protocol_deliver_rcu+0x14b/0x310
ip_local_deliver_finish+0x29d/0x390
ip_local_deliver+0x24d/0x2a0
Only grab the socket lock when SOCK_TIMESTAMP has to be set,
to keep the common case lockless.
-
CVE-2026-98268
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
perf: Fix null pointer access in is_include_guest_event()
A typical module unload occurring event when there is an active perf
connection leads to freeing of the pmu pointer. The call log is something
like:
..
__pmu_detach_event
pmu_detach_event
pmu_detach_events
perf_pmu_unregister
..
__pmu_detach_event() sets event-pmu to null. When the perf connection
finally is closed, the following stack trace is observed:
Oops: general protection fault, kernel NULL pointer dereference
...
RIP: 0010:_free_event+0x3e/0x370
...
Call Trace:
...
perf_event_release_kernel+0x260/0x2d0
perf_release+0x12/0x20
A call to mediated_pmu_unaccount_event() inside _free_event() is the root
cause of this crash. Adding a check inside is_include_guest_event() ensures
we don't accidentally access a null pmu ptr. In addition to this, we will
now call mediated_pmu_unaccount_event() before clearing the pmu ptr so that
nr_include_guest_events counts are maintained correctly.
-
CVE-2026-98257
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
rds: ib: use rds_conn_drop() on protocol version mismatch
rds_ib_cm_connect_complete() runs from the RDMA-CM event handler with
conn-c_cm_lock held. When the peer negotiates a protocol version
older than RDS_PROTOCOL_COMPAT_VERSION, the handler calls
rds_conn_destroy(), which is only safe in the rmmod path: it
synchronously tears the connection down and flush_work()es the
shutdown work cp_down_w.
That shutdown work (rds_conn_shutdown()) needs cp_cm_lock, which is
the very lock the event handler still holds, so the flush never
completes: the two workers wait on each other and the RDS connection
workqueues stall for good.
All other RDMA-CM failure paths (REJECTED, CONNECT_ERROR,
DISCONNECTED) use rds_conn_drop(), which marks the connection
RDS_CONN_ERROR and schedules the shutdown work asynchronously. Use
it here as well.
-
CVE-2026-98242
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
dma-buf: Fix silent overflow for phys vec to sgt
In case MMIO size is bigger than 4G and peer2peer DMA goes
through host bridge, we trigger a code path that assigns the
total linked IOVA (which is greater than 4G) to mapped_len.
Previously, `mapped_len` was declared as 32-bit `unsigned int`.
When accumulating `size_t` lengths, this leads to a silent wrap-around.
This truncation causes truncated lengths to be passed to functions
like `fill_sg_entry()`.
Fix this by changing `mapped_len` to `size_t` (64-bit). While
at it, fix similar potential overflow issues in `calc_sg_nents`
by using `check_add_overflow()` for `nents` and using
`unsigned int` for the loop iterator in `fill_sg_entry` to match.
-
CVE-2026-98241
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
ipv6: xfrm: use full sockets in local error paths
xfrm6_local_rxpmtu() and xfrm6_local_error() dereference skb-sk as if it
always pointed at a full IPv6 socket.
That is not guaranteed. TCP SYN-ACK skbs can be owned by a
TCP_NEW_SYN_RECV request_sock while the output path itself is driven by the
full listener. If rerouting selects an IPv6 XFRM tunnel route with a lower
MTU, the local PMTU/error handling path can reach these callbacks with that
mini-socket still attached to the skb.
The callbacks then miscast the request socket as a full inet/IPv6 socket and
can read beyond the request_sock allocation when they access inet_sock or
ipv6_pinfo state.
Resolve the owner with skb_to_full_sk() in both callbacks and bail out when
no full socket is attached. This matches the surrounding XFRM IPv6 PMTU/error
logic, which already reasons about full sockets with skb_to_full_sk().
-
CVE-2026-98237
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: wwan: mhi_wwan_mbim: guard against a cyclic NDP chain
The NDP traversal in mhi_mbim_rx() only stops when wNextNdpIndex is
zero. Nothing requires the offsets to advance, so a modem that
points an NDP at itself, or at an earlier NDP, keeps the loop
spinning forever on one CPU.
Break out when the next NDP offset is not larger than the current
one.
Verified in a QEMU guest with a fault injector feeding the driver's
receive callback an NTB whose single NDP points at itself: the
unpatched driver spins in mhi_mbim_rx() with one CPU pinned at 100%
and the thread never returns. With this check the loop terminates
within one iteration.
Changes in v2: move the non-increasing check to the wNextNdpIndex
retrieval site, as suggested by Loic Poulain, instead of tracking
the previous offset in a separate variable.
-
CVE-2026-98229
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
xfrm: save input state data before secpath resets
xfrm_input() stores the current xfrm_state in the skb secpath while it
continues receive-side processing. Some input paths can reset that secpath
before xfrm_input() has finished dereferencing the state.
Receive callback users such as VTI and XFRM interfaces can reset the
secpath. The VTI receive path does so before checking whether the packet
crosses network namespaces, while the XFRM interface path does so only for
cross-network-namespace packets. The XFRM_MAX_DEPTH error path can also
reset the secpath before the final drop callback reports the current
state's protocol.
If secpath_reset() drops the last state reference while the state is
concurrently deleted, xfrm_input() can still dereference the freed state
when selecting transport_finish() or reporting the drop callback protocol.
Save the state protocol on the stack while the state is still valid,
and use the already saved address family for transport_finish(). A larval
XFRM_STATE_ACQ state has no type, so retain nexthdr as its protocol. This
preserves the existing drop-path fallback while avoiding the post-reset
state dereferences without adding an extra state reference to every
received packet.
-
CVE-2026-98227
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
memstick: ms_block: destroy io_queue workqueue on removal
msb_init_disk() creates the per-card ordered workqueue msb-io_queue with
alloc_ordered_workqueue(). It is torn down with destroy_workqueue() only
on the init error path; msb_remove() never destroys it. msb_stop() merely
flushes the queue, and neither msb_data_clear() nor put_disk() free it. As
a result every card insert/remove cycle leaks the workqueue and its
kworker, exhausting kernel memory over repeated cycles.
Destroy the workqueue in msb_remove() after the disk has been removed and
the queue drained.
-
CVE-2026-98225
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mm/shrinker: fix bogus set_shrinker_bit() with cgroup.memory=nokmem
With cgroup.memory=nokmem, shrinker_memcg_alloc() bails out early and
never allocates an id, so shrinker-id keeps the 0 it got from the
kzalloc() in shrinker_alloc(). __list_lru_init() then copies that 0 into
lru->shrinker_id, where it looks like a valid bit index.
Nothing calls expand_shrinker_info() on nokmem either, so shrinker_nr_max
stays 0 and every memcg ends up with an empty map (map_nr_max == 0).
deferred_split_folio() hands a real memcg to __list_lru_add() regardless
of whether the lru is memcg aware, so the first THP queued in a cgroup
does set_shrinker_bit(memcg, nid, 0) and trips the bounds check:
WARNING: mm/shrinker.c:212 at set_shrinker_bit+0x7d/0x90, CPU#126
Call Trace:
TASK>
deferred_split_folio+0x18c/0x220
map_anon_folio_pmd_nopf+0xdd/0x130
map_anon_folio_pmd_pf+0x14/0xb0
do_huge_pmd_anonymous_page+0x1a1/0x620
__handle_mm_fault+0xea9/0x10d0
handle_mm_fault+0xe5/0x320
do_user_addr_fault+0x1cc/0x870
exc_page_fault+0x81/0x1b0
asm_exc_page_fault+0x27/0x30
Harmless, the WARN_ON_ONCE() is what keeps the out of bounds unit[] read
from happening, but the id should not look valid in the first place.
Clear it before returning.
Two other spots could paper over this: drop the id in __list_lru_init()
when nokmem turns memcg_aware off, or make deferred_split_folio() pass
NULL like list_lru_add_obj() does. Both leave shrinker->id lying around
for the next caller, so fix it where the id is handed out.
-
CVE-2026-98218
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
i2c: atr: fix dangling adapter pointer on add failure
i2c_atr_add_adapter() stores atr-adapter[chan_id] before
i2c_add_adapter() so that the I2C bus notifier can match child clients
during registration. On failure the channel is freed but the slot was
left pointing at freed memory, which can lead to use-after-free in
i2c_atr_del_adapter() / cleanup and also block reuse with -EEXIST.
Clear the slot on the i2c_add_adapter() error path before freeing chan.
-
CVE-2026-98210
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mmc: mxcmmc: cancel data work and watchdog on remove
mxcmci_remove() frees the host through the devm tail, but neither it nor
mmc_remove_host() drains the driver's own asynchronous state.
host-watchdog, a 10 s timer armed on the DMA path in mxcmci_setup_data(),
is deleted only by the DMA- and IRQ-complete paths, which the remove path
does not explicitly drain; it can therefore fire after the host is freed
and dereference it in mxcmci_watchdog(). host->datawork, armed from the
IRQ handler on the PIO path, is not cancelled by the remove path either.
Free the devm-registered IRQ, then cancel datawork and delete the watchdog
in mxcmci_remove(), before dma_release_channel(). Freeing the IRQ first
keeps a trailing handler from re-arming datawork between the cancel and
the host free. Both callbacks are non-self-rearming.
This issue was found by an in-house static analysis tool.
-
CVE-2026-98209
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mmc: sdhci-of-aspeed: Remove children before releasing SDC resources
Probe failure and removal leave SDHCI child devices registered after the
parent clock and managed resources are released.
Unregister the OF children in reverse order before disabling the parent
clock on both paths. Use of_platform_device_destroy() because manual
child creation does not set the flag required by of_platform_depopulate().
This issue was identified during our ongoing static-analysis research
while reviewing kernel code.
-
CVE-2026-98207
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mmc: spi: reset bytes_xfered before retrying CRC failures
mmc_spi_data_do() updates data-bytes_xfered after each block has been
transferred successfully. If a later block in the same data request
fails with a CRC error, data->bytes_xfered may therefore contain the
number of bytes completed before the failing block.
mmc_spi_request() has a private recovery path for such CRC failures. It
sends STOP_TRANSMISSION, clears data->error and jumps back to
crc_recover to issue the same command and data request again. However,
it does not clear data->bytes_xfered before the retry.
If the retry succeeds, the request is completed with the bytes from the
failed attempt still included in data->bytes_xfered. For a multi-block
request this can make the completed request report more bytes than were
transferred by the successful retry, and can even exceed the request size
when most blocks completed before the CRC error.
This is most likely to be observed on MMC-over-SPI systems where long
multi-block transfers occasionally hit a data CRC error but the
mmc_spi-internal retry succeeds. The data itself is retried, but the
completion accounting is not.
Clear data->bytes_xfered together with data->error before repeating the
request so the final completion reports only the bytes transferred by the
successful attempt.
-
CVE-2026-98205
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
Input: evdev - zero absinfo before partial copy in EVIOCSABS
The EVIOCSABS handler copies at most the user supplied ioctl size into
an uninitialized on-stack struct input_absinfo:
if (copy_from_user(&abs, p, min_t(size_t,
size, sizeof(struct input_absinfo))))
The size comes from _IOC_SIZE() of the ioctl command and is therefore
fully controlled by userspace. A short size leaves the trailing part of
the structure holding whatever was on the kernel stack, and the whole
structure is then stored into the device:
dev-absinfo[t] = abs;
EVIOCGABS hands that back to userspace, disclosing the stale stack
bytes. Only the resolution field is currently cleared, which covers the
legacy struct layout but not an arbitrarily short size.
Zero the structure before the copy so any part not supplied by the
caller reads back as zero. The existing resolution fixup is kept, since
it also handles a size that partially overlaps that field.
-
CVE-2026-98201
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
Input: zero ff_effect before compat copy in input_ff_effect_from_user
In the compat path input_ff_effect_from_user() aliases the caller's
native struct ff_effect with the smaller struct ff_effect_compat and
copies only the compat sized prefix:
compat_effect = (struct ff_effect_compat *)effect;
if (copy_from_user(compat_effect, buffer,
sizeof(struct ff_effect_compat)))
The tail of the native structure is never written. Callers pass an
uninitialized on-stack object, for example evdev_do_ioctl() for
EVIOCSFF, so those bytes keep their previous stack contents.
input_ff_upload() then stores the full native structure in
ff-effects[id], from where a uinput based force feedback daemon can
read it back via UI_BEGIN_FF_UPLOAD, disclosing kernel stack memory to
userspace.
Zero the effect before the compat copy.
-
CVE-2026-98193
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: libipw: reject TKIP frames without a full MIC
libipw_michael_mic_verify() assumes that an skb contains an eight-byte
Michael MIC. A short TKIP frame makes the unsigned payload length wrap,
causing michael_mic() to read past the skb.
Check that the MIC is present before verifying it, and use the existing
MICHAEL_MIC_LEN constant for all MIC lengths in the verifier.