-
CVE-2026-98254
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
swiotlb: use the adjusted address for the highmem page lookup
swiotlb_bounce() reads the page frame number from the slot's recorded
orig_addr, then advances orig_addr by tlb_offset to reach the address
the caller asked about. The highmem branch mixes the two: the offset
within the page comes from the adjusted address, the page from the value
before it.
Once the adjustment crosses a page boundary the pair no longer describes
one location, and the whole copy lands one page below the intended one
for a positive tlb_offset, one above for a negative one. DMA_FROM_DEVICE
writes the device data over the wrong page and leaves the intended one
stale, DMA_TO_DEVICE feeds the device from a page the mapping may not
cover. Partial syncs through dma_sync_single_range_for_*() are what make
tlb_offset non-zero.
The branch test is picked the same way, so a slot recorded in lowmem can
be adjusted into highmem and the lowmem path then hands a highmem
address to phys_to_virt().
Take both from orig_addr once it is final and keep pfn in the branch
that uses it. PhysHighMem() asks the question straight from the address,
as dma-debug already does.
-
CVE-2026-98250
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix handling of NFSEXP_PNFS in the netlink codepath
The rework of how block layouts were checked moved the check for
NFSEXP_PNFS out of nfsd4_setup_layout_type() and into the callers. That
patch didn't account for the new call in nfsd4_setup_layout_type().
-
CVE-2026-98249
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
arm64: hibernate: pass HVC_SET_VECTORS args to the resume hvc
swsusp_arch_suspend_exit() reinstalls the restored kernel's hyp stub
vectors with an hvc, but never passes the arguments. x0 is not set to
HVC_SET_VECTORS and x1 is not set to the vector address, so the stub
dispatch falls through and returns without writing vbar_el2. EL2 is
left pointing at the trans_pgd copy of the vectors, a page that
swsusp_free() releases right after resume.
Set the arguments up the same way __hyp_set_vectors() does.
Without this fix, Vladimir was able to trigger a hang when resuming from
hibernation with CONFIG_PAGE_POISONING=y and page_poison=on.
-
CVE-2026-98245
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
btrfs: take commit root semaphore when iterating in mark_block_group_to_copy()
mark_block_group_to_copy() iterates over the commit root with
skip_locking=true. A concurrent transaction commit can swap and free
the commit root during iteration, causing use-after-free when
accessing extent buffers.
Fix it by using path-need_commit_sem to protect the commit root search.
-
CVE-2026-98240
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: ip_tunnel: initialize `options_len` before referencing options
The following command triggers a kernel panic:
ip link add d0 type dummy; ip link set d0 up
ip route add 10.30.0.0/16 \
encap ip id 300 geneve_opts 4660:66:11223344 dev d0
memcpy: detected buffer overflow: 4 byte write of buffer size 0
kernel BUG at lib/string_helpers.c:1044!
...
ip_tun_parse_opts.part.0.cold+0x10/0x10
ip_tun_build_state+0x116/0x2a0
On kernels built with GCC 15+ and `CONFIG_FORTIFY_SOURCE`, the fortified
`memcpy()` got 0 sized destination with request of 4 bytes length:
static int ip_tun_parse_opts_geneve(...)
{
...
attr = tb[LWTUNNEL_IP_OPT_GENEVE_DATA];
data_len = nla_len(attr); /* == 4 */
struct geneve_opt *opt = ip_tunnel_info_opts(info) + opts_len;
memcpy(opt-opt_data, nla_data(attr), data_len);
/* ^^^^^^^^^^^^^ 0 since options_len is assigned afterwards */
Fixed by initializing the counter before the options are referenced.
Matching what `tunnel_key_opts_set()` already does.
-
CVE-2026-98235
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
net/sched: act_api: release tail references on DELACTION failure
A batched RTM_DELACTION request takes a temporary reference on each
action before attempting any deletion. tcf_action_delete() clears
each processed slot and drops its temporary reference before attempting
the deletion. If deletion fails, tca_action_gd() calls
tcf_action_put_many() to release the remaining references, but its
tcf_act_for_each_action() iterator stops at the first NULL slot.
When a batch stops at an action bound to a filter, this leaks a
reference on each subsequent action. A later delete of an unbound
action can then return success without removing it from the IDR.
Walk the full array in tcf_action_put_many() and skip NULL slots to
release the references held on the unprocessed actions.
-
CVE-2026-98224
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mm/vma: correctly unaccount on mmap_prepare() failure
__mmap_setup() accounts memory for relevant mappings via:
security_vm_enough_memory_mm()
- __vm_enough_memory()
-> vm_acct_memory()
If __mmap_setup() fails, this indicates that this accounting did not take
place, and thus it's appropriate for __mmap_region() to jump to
abort_munmap.
However if call_mmap_prepare() fails, it also jumps there and any accounted
memory is not correctly unaccounted.
Fix this by handling each error separately.
-
CVE-2026-98222
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
KEYS: encrypted: fix integer overflow of datablob_len
encrypted_key_alloc() stores datablob_len in a u16. It is computed from
multiple string and payload lengths. If the result exceeds U16_MAX, the
assignment truncates the allocation size. KASAN reports a 32760-byte
slab-out-of-bounds write when __ekey_init() copies the master key
description into the undersized buffer.
The total payload length stored in key-datalen is also a u16. Use
check_add_overflow() to reject values that do not fit either destination,
and use kzalloc_flex() for the flexible-array allocation.
-
CVE-2026-98219
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Close the pre-enable ops error claim window
scx_alloc_and_add_sched() publishes ops-priv before
scx_root_enable_workfn() switches the state to SCX_ENABLING. An error
claimed via scx_bpf_error_bstr() from an associated BPF program in that
window is consumed by scx_disable_workfn(), which takes the pre-enable
shortcut in scx_root_disable(). The shortcut returns without any teardown
and restores SCX_DISABLED with an unconditional scx_set_enable_state() xchg
racing the enable workfn's own transition. The enable then completes with
the claim consumed: the scheduler stays up but can never be disabled again,
and bpf_scx_unreg() frees it while still in use, resulting in a
use-after-free. Both WARN_ON_ONCE()s fire back to back:
WARNING: kernel/sched/ext/ext.c:7522 at
scx_root_enable_workfn+0xeec/0x1be0, CPU#3: scx_enable_help/276
WARNING: kernel/sched/ext/ext.c:6398 at scx_root_disable+0xb50/0xdb8,
CPU#0: sched_ext_helpe/664
scx_root_enable_workfn() switches to SCX_ENABLING before the scheduler
allocation, so ops->priv is never visible while SCX_DISABLED. The allocation
failure path restores SCX_DISABLED.
-
CVE-2026-98214
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
selinux: recheck intermediate backing files on mprotect()
mprotect() can be used to bypass the SELinux checks that mmap() performs
against the intermediate layers of a stacked filesystem.
mmap() checks every backing layer as the request descends through the
stack. mprotect() only has the lowest backing file in vma-vm_file, so it
rechecks the top-level user and the lowest mounter, but skips the mounters
of every layer in between. With two nested overlayfs mounts and a policy
denying mounter_t -> middle_file_t:file { execute }, a direct
mmap(PROT_EXEC) is denied:
avc: denied { execute } for pid=71 comm="nested_exec"
path="/payload" dev="overlay" ino=9
scontext=user_u:base_r:mounter_t
tcontext=user_u:object_r:middle_file_t tclass=file permissive=0
while mmap(PROT_NONE) followed by mprotect(PROT_EXEC) succeeds.
Preserve each intermediate path, mounter SID and file-description SID in
the backing-file security blob, copying the saved entries when another
backing layer is opened. Allocate the array only for nested backing files,
and release it and the path references in the backing_file_free hook.
During mprotect(), recheck fd { use } and the requested inode permissions
for every saved mounter, and include the intermediate layers in the execmod
checks. Policy for nested stacking may then need to grant intermediate
mounters what a direct mmap() already requires, and execmod on intermediate
labels for binaries using text relocations.
Tested on arm64 QEMU with a small BusyBox initramfs and a purpose-built
SELinux policy, on a mainline tree containing
commit f2381b546e7e ("fs: fix user path of nested backing files").
[PM: subject tweak]
-
CVE-2026-98213
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mmc: core: Cancel SDIO IRQ work before freeing host
A host controller that uses sdio_signal_irq() schedules host-sdio_irq_work
from its interrupt handler. That work is only cancelled on the suspend
path (mmc_sdio_suspend()), not on the remove/free path, so a worker armed
just before the controller freed its IRQ can run after
mmc_host_classdev_release() has freed the host and dereference it through
container_of().
Cancel host->sdio_irq_work in mmc_free_host(), like the existing
host->detect drain added by commit 1036f69e2513 ("mmc: core: Cancel
delayed work before releasing host").
This issue was found by an in-house static analysis tool.
-
CVE-2026-98211
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
mmc: mmci: Fix use-after-free in busy-timeout work
ux500_busy_complete() can queue ux500_busy_timeout_work for an R1b
command, but mmci_remove() never cancels it. The work can subsequently
dereference the devm-allocated mmci_host after it has been released.
Mask the controller interrupts and disable the delayed work during
removal. This drains any queued instance and stops an IRQ handler that
is still in progress from queueing the work again once it has been
disabled.
This issue was found by an in-house static analysis tool.
-
CVE-2026-98203
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
Input: soc_button_array - check btns_desc-package.count
Check that btns_desc->package.count is not 0 before accessing
btns_desc->package.elements[0].
-
CVE-2026-98202
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - fix GPF in suspend and resume when unbound
Transport drivers (such as rmi_i2c and rmi_spi) invoke
rmi_driver_suspend() and rmi_driver_resume() on their child rmi_dev
device during system power management events. However, transport drivers
are fully registered and operational even if the physical RMI driver
failed to bind or probe the rmi_dev device.
When rmi_driver_suspend() or rmi_driver_resume() is called on an unbound
rmi_dev, dev_get_drvdata() returns NULL. Calling rmi_disable_irq() or
rmi_enable_irq() without driver data attached causes a NULL pointer
dereference and General Protection Fault when attempting to lock
data-enabled_mutex.
Fix this by checking if driver data is attached to rmi_dev in
rmi_driver_suspend() and rmi_driver_resume(), exiting early if
no driver data is present.
-
CVE-2026-98198
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pwm-fan) Stop RPM timer before freeing tach data
sample_timer() rearms the RPM timer and accesses the devm-managed
ctx-tachs and ctx->pulses_per_revolution arrays. The cleanup action
which stops the timer is registered before those arrays are allocated.
Since devres releases entries in reverse order, driver detach can free
the arrays before pwm_fan_cleanup() shuts down the timer. A timer expiry
in that window accesses the freed tach data.
With a KASAN kernel, a test-only kprobe delayed entry to
pwm_fan_cleanup() while normal sysfs unbind ran. Each of three runs
reported three four-byte reads and two four-byte writes in sample_timer()
after its backing devm allocations had been freed. The helper did not
invoke the timer callback, cleanup actions or free functions.
With the fix, three matching unbind runs completed without KASAN, BUG,
WARNING, Oops or panic. Instrumentation confirmed that timer retirement
completed before the first timer backing allocation was released.
Split timer retirement from the power cleanup and register its devres
action after the timer backing data and IRQ actions are installed. This
preserves the early power rollback action while ensuring the timer is
retired before its backing data is released. Use timer_shutdown_sync()
because the callback can rearm itself.
-
CVE-2026-98195
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlegacy: fix broadcast stations deallocation
On the error path of __il4965_up(), il_dealloc_bcast_stations() clears
only IL_STA_UCODE_ACTIVE, leaving IL_STA_BCAST set. This causes the
same broadcast stations to be deallocated again by __il4965_down().
This can occur when RF_KILL is toggled during driver startup.
To fix clear the entire 'used' field, since we will not do any
other operations on the station.
-
CVE-2026-98187
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
wifi: p54: require a full exp_if record in PDR_INTERFACE_LIST
The PDR_INTERFACE_LIST loop only checks that the record start is within
the entry before reading an entire struct exp_if from it. A truncated
trailing record makes the if_id/variant reads cross the entry boundary
into the heap beyond the EEPROM buffer (verified with a KASAN
reproducer of the loop). The variant also feeds the synth front-end
selection, so this is not only a leak.
Advance only while a full record still fits in the entry.
-
CVE-2026-98179
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix rmmio iounmap skipped on device removal
amdgpu_pci_remove() calls drm_dev_unplug() before fini_sw(), so
drm_dev_enter() is already false there and the iounmap() guarded by it
is skipped. This .remove path runs on both hot-unplug and plain rmmod,
so the register BAR ioremap mapping leaks one instance per unload.
Unmap rmmio unconditionally (guard only on non-NULL) and drop the now
unused idx.
(cherry picked from commit dd6f86a97260e5207d3329ad03aa89fdad61b1e6)
-
CVE-2026-98175
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
smb: client: cancel reconnect work in clean_demultiplex_info()
clean_demultiplex_info() cancels server-echo delayed work but not
server->reconnect, which can cause a use-after-free when the
demultiplex thread exits while a reconnect work is still queued:
cifs_demultiplex_thread()
cifs_readv_from_socket()
cifs_reconnect()
__cifs_reconnect()
cifs_queue_server_reconn()
mod_delayed_work(cifsiod_wq, &server->reconnect, 0)
clean_demultiplex_info()
cancel_delayed_work_sync(&server->echo) // echo canceled
// reconnect NOT canceled
kfree_sensitive(server) // server freed
...later, on cifsiod_wq:
smb2_reconnect_server()
server->srv_count // UAF read of freed server
Fix this by canceling server->reconnect delayed work in
clean_demultiplex_info() before the server is freed, the same way
cifs_put_tcp_session() already does.
-
CVE-2026-98173
•
published on October 6, 2026
In the Linux kernel, the following vulnerability has been resolved:
smb: client: fix use-after-free of iface in cifs_try_adding_channels()
cifs_try_adding_channels() iterates ses-iface_list with
list_for_each_entry_safe_from(), which captures the next entry
(niface) under iface_lock. The loop body then drops iface_lock for
the whole duration of cifs_ses_add_channel().
A concurrent interface refresh (SMB3_request_interfaces() ->
parse_server_interfaces()) marks all ifaces inactive and removes and
frees any that are not re-advertised via list_del() + kref_put(),
where release_iface() is a bare kfree(). Since niface typically has
no channel holding a reference, the list reference is its last and it
can be freed inside the unlocked window. On continue, the iterator
advance step then dereferences niface->iface_head.next, and the loop
body reads iface->rdma_capable/is_active, both on freed memory.
Fix this by never keeping an unreferenced list pointer across the
unlocked window. Each channel attempt now re-scans the list from the
head under iface_lock, takes a kref on the selected candidate, and
passes only that referenced candidate to cifs_ses_add_channel().
weight_fulfilled still tracks selection progress, so restarting the
scan preserves the original weighted distribution and the
weight_fulfilled-before-kref_put ordering on the failure path.
Add a per-pass attempts cap so a flapping interface refresh cannot
keep the inner loop spinning within a single tries increment.