-
CVE-2026-97961
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
perf/core: Allow list_del during perf_event_overflow()
A PMU might use perf_sched_cb_inc() and perf_sched_cb_dec()
interface to get the PMU call back function pmu::sched_task
invoked at schedule in and schedule out. This is achieved
by walking along the list anchored by sched_cb_list.
The following scenario might lead to a list corruption.
perf_pmu_sched_task()
for_each_list_entry(..., &sched_cb_list)
+-- __perf_pmu_sched_task()
+--> event->pmu->sched_task())
+--> PMU_push_sample()
+--> perf_event_overflow()
+--> __perf_event_overflow()
+--> pmu->stop()
+--> perf_sched_cb_dec()
remove entry from sched_cb_list
while list node in use.
This happens when ioctl(fd, PERF_EVENT_IOC_REFRESH, xxx) has been
invoked and perf_event::event_limit hits zero.
Prevent the list corruption and convert for_each_list_entry()
to for_each_list_entry_safe().
-
CVE-2026-97959
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_route: free emptied bucket on filter move
route4_change can move an existing filter to a different top-level
bucket: route4_set_parms recomputes the handle from TCA_ROUTE4_TO/
FROM/IIF, and the handle-mismatch check is gated on the 'new' flag, so
for an existing filter the new handle may differ from the old one and
land in a different bucket. When this happens, the filter is unlinked
from the old bucket, but the bucket itself is never freed once it goes
empty. The stale empty bucket remains in head-table[], causing
route4_delete to report *last=false even after the last live filter is
gone. That pins the empty tcf_proto and causes a leak.
Fix this by refcounting the filters linked to a bucket and freeing the
bucket when the count drops to zero. The existing scan in route4_delete
goes away with it.
The count is updated at all sites that link or unlink a filter during add,
change and delete, and the bucket is dropped from head->table[] as soon as
it reaches zero.
Conditions to recreate the bug:
CONFIG_NET_CLS_ROUTE4=y, CONFIG_NET_SCH_INGRESS=y, CONFIG_NET_CLS_ACT=y.
tc qdisc replace dev lo clsact
tc filter add dev lo ingress protocol ip pref 100 route from 1 to 1
tc filter change dev lo ingress protocol ip pref 100 handle 0x10001 \
route from 1 to 2
tc filter del dev lo ingress protocol ip pref 100 handle 0x10002 \
route from 1 to 2
tc filter show dev lo ingress | grep -c 'pref 100 route chain 0 '
-
CVE-2026-97957
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
net: hinic: fix mailbox segment buffer overflow
check_mbox_seq_id_and_seg_len() validates that seq_id does not
exceed SEQ_ID_MAX_VAL (42) and seg_len does not exceed
MBOX_SEG_LEN (48). However, this allows the last segment
(seq_id=42) to carry a full 48-byte payload, writing to offset
42*48=2016 for 48 bytes (ending at byte 2064). The receive
buffer is only MBOX_MAX_BUF_SZ (2048) bytes, resulting in a
16-byte heap buffer overflow.
The hinic3 driver already handles this correctly by defining
MBOX_LAST_SEG_MAX_LEN and rejecting the last segment when it
exceeds the remaining buffer space. Apply the same fix to the
hinic driver.
-
CVE-2026-97952
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
sunvdc: unmap LDC cookies when the descriptor send fails
__send_request() maps the request's pages into the LDC channel's map
table (ldc_map_sg()), fills in the descriptor and marks it
VIO_DESC_READY before ringing the doorbell via __vdc_tx_trigger().
When the trigger fails, the error path only prints a message: the
descriptor stays READY and the cookies are never unmapped. The
mapping is normally released in vdc_end_one() when the peer completes
the descriptor - but a descriptor whose doorbell was never sent will
never complete, and since dr-prod is not advanced on failure, the
reset path (vdc_requeue_inflight(), which walks [cons, prod)) never
visits it either. The map table entries are leaked permanently.
Since commit a11f6ca9aef9 ("sunvdc: Do not spin in an infinite loop
when vio_ldc_send() returns EAGAIN") trigger failures occur in
practice under load, so every resulting I/O error also leaks one
request's worth of entries from the fixed-size (8192 entries per
channel) map table. Because the allocator hands out contiguous
ranges, fragmentation makes large multi-segment requests fail first
as the table drains, until ldc_map_sg() fails permanently and the
disk is dead until reboot.
It also makes any retry-based recovery unusable: requeuing the
request on -EAGAIN remaps the pages on every attempt, overwriting
desc->cookies and orphaning the previous mapping, so the table
drains at the retry rate. This is the memory exhaustion observed
when the requeue approach was first tested in October 2025.
Roll back on failure: unmap the cookies, mark the descriptor FREE
again and clear the request entry. If the trigger failed with
-ENOTCONN, __vdc_tx_trigger() has already reset the port, which
tears down and reallocates both the dring and the LDC channel
including its map table - nothing to roll back, and the stale
descriptor must not be touched.
-
CVE-2026-97951
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
scsi: target: iscsi: Fix hang for aborted WRITE_PENDING commands
When a LUN_RESET aborts a WRITE command that is in the
TRANSPORT_WRITE_PENDING state, the target core sets CMD_T_ABORTED and
waits for the frontend to finish processing.
If the initiator subsequently sends the remaining dataout PDUs,
__iscsit_check_dataout_hdr() catches the payload, stops the dataout
timer if the sequence is final and finally dumps the data. However, the
iSCSI target doesn't trigger the completion process for these aborted
commands. Because of this, the abort path hangs indefinitely in
target_put_cmd_and_wait(), leading to a deadlocked target worker thread.
Fix this by explicitly calling target_complete_cmd() when the final
dataout PDU is received for an aborted WRITE command.
target_complete_cmd() detects the CMD_T_ABORTED flag and cleanly routes
the command into target_abort_work, allowing the abort completion to
successfully unblock.
-
CVE-2026-97924
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
tracing/user_events: Don't destroy fields when event removal fails
destroy_user_event() destroys the event's fields before attempting to
remove the trace event call. If user_event_set_call_visible() fails,
e.g. because the event is still enabled and trace_remove_event_call()
returns -EBUSY, the event is left registered with an irreversibly
destroyed field list. Any subsequent interaction with the event then
operates on an empty field list while it is still fully visible in
tracefs.
Move the field destruction after the call removal, and splice the
field list back onto the event when the removal fails so the event
remains in a consistent state.
-
CVE-2026-97923
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
tracing: Free histogram the var ref when its initialization fails
create_var_ref() allocates a VAR_REF hist_field and then calls
init_var_ref() to fill it in. When that fails the field is leaked.
commit 656fe2ba85e8 ("tracing: Use hist trigger's var_ref array to destroy
var_refs") made destroy_hist_field() return early for
HIST_FIELD_FL_VAR_REF, since var refs are freed by walking the trigger's
var_refs[] array instead. create_var_ref() adds the field to that array
only after init_var_ref() has succeeded, so on this path the field is in
neither place and nothing frees it. The call was correct when it was
written, before var refs were taken out of destroy_hist_field().
init_var_ref() cannot free it either. The caller owns the field, so
init_var_ref() undoes only its own string allocations and leaves the
field alone. Freeing it there would leave create_var_ref() passing freed
memory to destroy_hist_field(), which reads its flags.
Call __destroy_hist_field(), which frees the field without consulting
the flag.
-
CVE-2026-97919
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
tracing: Take the reference before publishing the named histogram trigger
event_hist_trigger_named_init() puts the trigger on the global
named_triggers list and only then takes the reference on the trigger it
shares its histogram with:
data-ref++;
save_named_trigger(data->named_data->name, data);
ret = event_hist_trigger_init(data->named_data);
if (ret 0) {
kfree(data->cmd_ops);
data->cmd_ops = &trigger_hist_cmd;
}
return ret;
event_hist_trigger_init() fails when alloc_hist_pad() cannot allocate, and
nothing takes the trigger back off the list on the way out.
event_hist_trigger_parse() frees it, and the next lookup by name reads the
freed object:
BUG: KASAN: slab-use-after-free in find_named_trigger+0xac/0xc0
Read of size 8 at addr ffff888009346860 by task init/1
find_named_trigger+0xac/0xc0
hist_register_trigger+0xc1/0xa00
event_hist_trigger_parse+0x3146/0x6af0
event_trigger_write+0xce/0x160
Freed by task 67:
kfree+0x154/0x420
trigger_kthread_fn+0xfd/0x160
Do the reference first and publish once it has succeeded, so that nothing
which can fail runs after the trigger becomes findable.
-
CVE-2026-97916
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Validate firmware log buffer metadata
The tracing log headers parsed by fw_log_print_buffer() reside in
DMA-shared BOs that the NPU firmware can write to.
fw_log_from_bo() validated log-header_size and log->size, but
fw_log_print_buffer() re-read those same fields from shared memory
afterwards, allowing a TOCTOU where firmware changes them between the
check and the use, and making the host dereference out-of-bounds
addresses while printing logs.
Snapshot the validated values once with READ_ONCE() and pass them down
explicitly in a new struct ivpu_fw_log_desc instead of re-reading them
from the shared struct.
-
CVE-2026-97910
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
ASoC: sprd: validate compress buffer sizes against fixed allocations
sprd_platform_compr_open() allocates the stage 0 IRAM buffer (32K data
area) and the stage 1 DDR buffer (2M data area) with fixed sizes, but
sprd_platform_compr_copy() derives all copy lengths from the user
controlled runtime-fragment_size and the write() count, never
comparing them against the physical buffer sizes. The compress core
only checks fragment_size * fragments for an u32 overflow in
snd_compress_check_input(), so a local user can configure a logical
buffer of up to ~4GB via SNDRV_COMPRESS_SET_PARAMS, far exceeding the
fixed allocations.
A fragment_size larger than the 32K IRAM data area makes the stage 0
copy_from_user() overflow past the IRAM allocation, and a buffer_size
larger than the 2M DDR buffer makes the wrapping copy at the end of
sprd_platform_compr_copy() write fully user controlled data past the
buffer. No SNDRV_PCM_TRIGGER_START is needed, a write() in SETUP
state reaches the copy callback directly.
Reject parameters that do not fit into the fixed buffers in
set_params(), and fix the advertised max fragment size: 128K never
fitted into the 32K IRAM buffer. The caps values may have been carried over
from the qdsp6 driver, which allocates its buffers according to the
advertised maxima, unlike this driver. With 32K as max fragment size
the advertised limits are self-consistent: 32K * 64 = 2M equals the
DDR buffer size.
Discovered by Atuin - Automated Vulnerability Discovery Engine.
-
CVE-2026-97906
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
bootconfig: Fix integer overflow in initrd size check
Sashiko reported that in get_boot_config_from_initrd(), a crafted initrd
with a huge bootconfig size (such as 0xFFFFFFFF) can cause the pointer
arithmetic:
data = ((void *)hdr) - size;
to wrap around on 32-bit systems (or when pointer subtraction overflows).
Because data wraps around, the subsequent bounds check:
if ((unsigned long)data initrd_start)
evaluates to false, bypassing the check. The kernel then calls
xbc_calc_checksum(data, size), which attempts to read 4GB of memory,
hitting unmapped pages and triggering a fatal kernel page fault during
early boot. Furthermore, on 64-bit systems with an initrd 4.29 GB, an
unbounded 32-bit size can similarly bypass the initrd_start check.
Fix this by:
1. Ensuring the initrd is at least large enough to contain the bootconfig
footer and verifying hdr is within the initrd bounds.
2. Checking that size does not exceed XBC_DATA_MAX and does not exceed
the available space between initrd_start and hdr before performing
pointer subtraction.
-
CVE-2026-97901
•
published on September 25, 2026
In the Linux kernel, the following vulnerability has been resolved:
genetlink: pin family module during policy dump
The generic netlink controller's policy dump keeps pointers to the target
family's operation and policy tables in its callback state. A dump may be
split across multiple skbs and remain pending after the initial request.
Netlink pins the module which owns the dump callback, but in this case
that is the controller's owner rather than the target family's owner. The
target family can consequently be unregistered and its module unloaded
while a policy dump is pending. Advancing the dump then dereferences
policy memory from the unloaded module.
Take a reference to the target family's module when the dump starts.
Drop it from the error and done paths. This matches the lifetime for which
the dump context retains the family and policy pointers.
-
CVE-2026-97897
•
published on September 25, 2026
A security flaw has been discovered in Krayin laravel-crm up to 2.2.5. This issue affects some unknown processing of the file Sanitizer.php of the component TinyMCE Media Upload. The manipulation results in cross site scripting. The attack may be performed from remote. Upgrading to version 2.2.6 is capable of addressing this issue. The patch is identified as 734aa10ae6c2ffa4c96c8869a89aa66940e4d345. You should upgrade the affected component.
-
CVE-2026-97891
•
published on November 10, 2026
In Eclipse Kura version 5.0.0 to 5.6.2, the Web Console allocates a new HTTP session for every request to its built-in authentication endpoints (/admin/auth, /admin/login/password, /admin/login/cert) before checking the HTTP method, parsing the request, or validating any submitted credentials, and does not limit how many such sessions can be allocated. An unauthenticated client that sends requests to these endpoints without honoring the returned session cookie can cause the server to allocate an unbounded number of sessions, exhausting the JVM heap and crashing the Kura process.
-
CVE-2026-97883
•
published on September 25, 2026
A security vulnerability has been detected in mathurvishal CloudClassroom-PHP-Project up to 5dadec098bfbbf3300d60c3494db3fb95b66e7be. This affects an unknown function of the file updatequery.php. The manipulation of the argument gid leads to sql injection. The attack can be initiated remotely. The exploit has been disclosed publicly and may be used. Continious delivery with rolling releases is used by this product. Therefore, no version details of affected nor updated releases are available. The vendor was contacted early about this disclosure but did not respond in any way.
-
CVE-2026-97875
•
published on September 25, 2026
Rojo's "rojo serve" HTTP API (default port 34872) has no Host/Origin header validation, making it vulnerable to DNS rebinding. A malicious webpage can read all project source, write malicious code to files on disk, and launch local programs via opener::open() with no user interaction beyond visiting the page.
-
CVE-2026-97867
•
published on November 10, 2026
The EJBd remote protocol returns datasource connection details, including database credentials, to remote clients that look up a datasource. A remote client able to reach the EJBd endpoint can obtain the database credentials and connect to the database directly. Users are recommended to upgrade to version 10.3.0 or 11.0.0-M2, which fix the issue.
-
CVE-2026-97858
•
published on October 16, 2026
An attacker can cause the server to unbind the target device from its current owner and rebind it to the requesting account, regardless of whether the device is currently bound to a different account, allowing an attacker to obtain the device's full serial ID.
-
CVE-2026-97844
•
published on October 13, 2026
Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network.
-
CVE-2026-97838
•
published on October 13, 2026
Out-of-bounds read in DNS Server allows an authorized attacker to disclose information over a network.